DIY sliding gates (57 photos) - types, features, installation instructions. How to make swing gates with your own hands: drawings Step-by-step installation of swing gates with your own hands

We will send the material to you by e-mail

Gates are an integral part of any fence or garage. Today you can make them yourself, the main thing is to choose the right type of design. They will help you make the gate yourself: drawings, photos and videos. This information will also help you decide on the material from which the structure will be made.

Gate in a private yard

A common option for everyone is swinging products. They are used in country houses, in private houses and in the construction of garages. A gate can also be located next to such options. The design involves the installation of two supporting elements along the edges of the canvas. Today it is quite easy to make swing gates with your own hands. Drawings, photos and videos will help you study all the intricacies of the work.

Arrangement of supporting elements

At the first stage of construction, it is necessary to install supports. Most often these are metal pillars of suitable diameter, which are concreted into the ground. Very often done with brick pillars. In this case, they can also be a support for the product. But do not forget, when laying bricks, to make metal embedded parts to which the hinges will be welded.

Preparing the sashes

From which side such hinges are welded depends on which direction they will open. That is why, when making a gate with your own hands: drawings, photos and videos must be viewed without fail. To make the sashes, a metal frame is most often used, onto which sheet material is attached. If the fence is wooden, then it is more expedient to make the gate from wood. In this case, the frame can be made from both metal corners and timber. It is important that the sashes are not too heavy, otherwise they will put a lot of stress on the posts and hinges. Over time, this can lead to deformation and the doors will not close well.

Therefore, it is worth studying some information before making swing gates with your own hands. Photo and video drawings will help you become familiar with all the intricacies of the work and prevent all sorts of defects. At the final stage, it is necessary to install a locking system on the doors. The simplest option may be a simple deadbolt.

Video: swing gates made of corrugated sheets and metal profiles

Features of sliding gates

Sliding options are increasingly being used during the construction of fencing. They take up relatively little space. In addition, the machine can be located just a few centimeters from the fence and this will not interfere with opening or closing them. The availability of a variety of building materials makes it possible for everyone to make sliding gates with their own hands. Drawings, photos and videos will allow you to more carefully study all the features of the work.

Sliding option

The main types of sliding gates:

console;
hanging;
recoil.

Hanging variety

The hanging option is not particularly popular. This is due to the fact that a rail is installed in the upper part along which the canvas moves. This rail is a kind of limiter, so not every vehicle will be able to enter the yard.

Sliding products

To operate sliding options, the rail is installed along the wall and directly in the opening itself. It is not practical to use such a system in the northern regions. Because with a large amount of snow, the operation of the shutters will be difficult, and snow-covered areas will constantly need to be cleared.

Advantages of the console type

The console type is by far the most popular. They can be used in both southern and northern regions. The movement of the canvas occurs above the ground, so there is no need to constantly clear the path. In addition, the advantage is that there are no restrictions at the top. This makes it possible for even high-height vehicles to enter the yard.

For an installation of this type, only one support column is required, which will bear the entire load from the canvas. Therefore, it is important to make it as high quality and reliable as possible. The cantilever beam itself on the gate can be located below, above or in the middle of the door leaf.

Helpful information! The beam located in the middle is considered the best option, since it generally strengthens the entire structure.

Recoil model

Everyone can handle making sliding gates with their own hands. Drawings, photos and videos allow you to study the principle of the sliding system. It is important to take into account all recommendations when performing work.

Features of sliding gates

Sliding options can significantly save space in the yard. But at the same time it is necessary to control the space along the fence. For the system to function properly, it is first necessary to clear the area of debris and any vegetation.

Installation of support elements

The beginning of the work is the installation of the main support column, which will bear the main load. If you wish, you can do it and the video will help you follow the technology. To work you need to prepare the following tools:

For the sashes themselves, it is best to use galvanized material. It is able to last a long time, while maintaining its original appearance. Polymer-coated corrugated sheets are often used.

Helpful information! The use of corrugated sheets is considered the most successful solution, since it is treated with special agents that prevent corrosion.

Products of this type can be equipped with automatic or manual drive.

Sliding type drawing

At the beginning of work, it is worth preparing drawings according to which the work will be carried out. Drawings and diagrams also allow you to calculate the exact amount of material required. The height of the gate must correspond to the fence. The width of the opening can be very different. Sliding products exert pressure not only on the rails, but also on the pole, so special attention must be paid to its design. Its lower part must be immersed in the soil and properly concreted.

Arrangement of rails for moving the web

Sliding gates will run on a rail that is located on the ground. To do this, you need to choose a U-shaped metal profile. Its length should be equal to two lengths of the canvas. For reserve you need to make another 30 centimeters. It is important that the rail is installed on a concrete base. Only in this way can you obtain the most reliable design that will last for a long time. After all the rail systems are installed and secured to the support pole, the electric drive can be installed.

Assembly of the canvas and its installation

The door leaf is made from a metal frame, to which a profiled sheet will subsequently be attached. Rollers are attached to the bottom of the metal frame. The door leaf is installed last. Do-it-yourself sliding gates: drawings, photos and videos provide complete information about the design and process of the work.

Tips and tricks for doing your own work

Every person can make a gate of any design. It is important to follow the recommendations of specialists and study some information beforehand.

Select only high quality materials for work. This will allow the structure to be used for a long period and no repair work will be required.
It is important to pay attention to all drawings and diagrams. Only strict adherence to the scheme will allow you to complete all the work correctly the first time. Compliance with dimensions and parameters makes it possible to make a functional design that will work without problems.
The installation of an electric type drive must be carried out with full understanding. If you have no experience in this field, you should entrust all the work to specialists. They will do everything efficiently and quickly. The products will open and close without difficulty.
If the use of a roller system is envisaged, special attention should be paid to its selection. It is best purchased in specialized stores. In this case, such a system will work flawlessly for a long time.

Today, you can supplement your fencing with a self-made gate. Various materials can be used for manufacturing. The most commonly used materials are wood and metal. Before you begin, you should consider what type of construction is best to use. Starting to make gates with your own hands: drawings, diagrams and photos will help you solve even complex problems. Swing gates are a classic option with a design that anyone can handle. Their arrangement requires a lot of space so that they open freely. You can save space in your garden using sliding or sliding gates.

Save time: selected articles delivered to your inbox every week

In this article we will try to tell you how to make swing gates with your own hands. You will understand that there is nothing complicated about it. When producing a sash, the most difficult thing is to weld the frame. If you do not know how to use welding, then hire a welder for a couple of hours.

How to make a gate with your own hands - choosing materials

Gates can be made of wood or metal. Please note that you are unlikely to be able to make decorative gates yourself with curved lines using forging; only a professional can do this. To make decorative gates you need equipment, a special room, expensive tools and, of course, experience. It is better to buy such gates ready-made. It would be wiser for a home craftsman to make a regular gate with a metal frame covered with profiled sheets.

How to make a gate with your own hands - installation of supports

If the yard is already fenced with a fence with support posts and a gate, then this greatly simplifies the matter. Secure the hinges by welding directly on them. If there are no supports, then you need to perform a number of simple steps.

Treat the metal supports with primer and paint them.
Depending on the width of the gate, you need to dig 2 holes 1.5 meters deep.
Place a cushion of sand and gravel at the bottom of the pit.
Insert the supports into the holes and secure them with reinforcement.
Align the supports plumb and fill with concrete.

Hinges can only be installed after the concrete has completely hardened.

How to make a gate with your own hands - gate frame

To make the frame correctly, you need to prepare a drawing of the metal structure in advance and at this stage adhere to a certain sequence of actions.

In accordance with the required dimensions indicated in the drawing, cut the metal pipe strictly at an angle of 45 degrees.
The frame must be assembled on a flat horizontal surface and immediately secured by welding.
Check the internal dimensions and compare the diagonals of the resulting frame.
Make the necessary adjustments and weld the frame completely.
In the sash where a gate is not provided, weld several corners from the inside for reinforcement.
In the second leaf, assemble a special opening in which the gate door will be fixed.
Once you have finished preparing the door opening, assemble the door. Using the prepared dimensions, assemble the frame of the gate in a strictly rectangular shape.
The rigidity of the gate door should be at the same level as the ribs on the leaf.
To give the structure additional rigidity, weld metal triangles in the corners.
Weld 2 cross members to the frame.
According to the drawing, weld the canopies and bolts in the required places.
After welding, the elements are ground and primed.
Paint the structure.

How to make a gate with your own hands - covering the frame with corrugated sheets

After the frame has dried, you can use corrugated sheeting to cover the frame. Place the profiled sheet on the frame and carefully attach it using rivets or self-tapping screws. The use of rivets allows you to get an attractive appearance.

Rivets and self-tapping screws must be secured in the recesses of the corrugated sheet. Consumption: for 1 square meter of corrugated sheeting you need to use at least 6 rivets or self-tapping screws. This quantity is due to the fact that in addition to the weight of the gate, they must withstand strong wind loads. After fixing the sheets of corrugated sheets, you can begin hanging the gate on the hinges.

How to make a gate with your own hands - installation nuances

Before installing swing gates, you need to make sure that the ground surface is even. Since most craftsmen make gates that can open in both directions, keep in mind that gates that open “pull” open more conveniently and last longer. Such gates are difficult to break open from the street side, since more force must be applied against the direction of opening than in the direction “along” the gate. This is important, because in critical situations every minute is valuable.

Making your own gates from corrugated sheets is a reliable and economical way to protect your property from prying eyes and uninvited guests. This entire system can be automated, which will improve the practicality and functionality of using the gate. Automated equipment is used for this.

In modern conditions, gates are not only a security element that partially reduces the likelihood of theft or damage to a car, as well as unauthorized entry into the site or garage, but also part of the overall interior of the garage, house or site. In this article we will talk about different types of gates, features of their installation and operation, advantages and disadvantages, and also tell you how to install them yourself.

What types of gates are there?

Despite the fact that most types of gates are universal, that is, they can be used for a house, garage or fence, there are gates that are only suitable for one thing. Therefore, we will list the main types of gates and also indicate what they are best suited for.

Swing.
Recoil.
Folding.
Retractable.
Sectional.

Swing gates

This is the most common and universal type of gate, which has not changed its design for thousands of years and consists of two vertical supports, several canopies (hinges) and two leaves. Depending on the material of the valves, they can be divided into:

solid;
with gaps;
wooden;
metal:
from sheet metal;
forged.

The main advantages of swing gates are ease of installation and maintenance, the main disadvantage is sensitivity to the amount of snow cover and dependence on the free space in front of them. If the snow has risen above the lower edge of the gate or there is any obstacle in front of it (a car, a pile of garbage, a FS unit), then opening it will be problematic; other types of gates do not have this drawback.

Sliding gates - drawing

The second most popular gate, which can be installed only where there is enough free space on the side, that is, 1.5–2 times the width of the gate opening. Because of this, they are installed only in fences and garages located in the basement or lower floor of a residential building. Despite the fact that there are sliding gates made partly from wood, they are not widely used, so almost all sliding gates are made of metal. At the same time, gates made of sheet, pipe and rod are in equal demand. The main advantage of these gates is that they do not require free space in front of them, but they require maintenance much more often than swing gates due to the more difficult operation of the rollers and carriages that ensure the movement of the gate.

Folding gate

This type of gate has become widespread in various enterprises because it does not have the main disadvantages of other types of gates and is located in a protected area. Due to the fact that the lower guide is closed by the gate, even during heavy snowfall it does not become clogged with snow, so there are no problems with opening the gate. Therefore, these gates have only two drawbacks - the high cost of the installation kit and installation, as well as a weak security effect, because they perform only a decorative and logistical function. However, if executed correctly, these gates will look very nice on the garage under the house. However, these gates are not widely used in residential buildings.

Retractable gate

Retractable or up-and-over gates are very popular in garages located inside protected areas. The gates do not depend on the level of snow and are relatively inexpensive, but they take up a lot of space under the ceiling, where they are removed when the garage is opened. Due to the fact that the gate is made in the form of one huge leaf, which completely covers the gate opening, their opening looks very beautiful - the gate rises, unfolds and goes somewhere inside the garage. In addition, such gates require regular professional maintenance, so they are installed only by those who can carry out all routine and repair work themselves or have sufficient finances to enter into a service agreement with a serious company.

Sectional doors

Sectional, or roller, gates are the best choice for a garage located inside a protected area. They do not depend on the amount of snow cover, do not require a large space under the ceiling (with the exception of large-section doors), and are easy to maintain. Thanks to the use of modern materials, they provide good insulation of the garage without any additional measures, because the insulation is located inside the metal (less often plastic) frame from which the sections are made. Such gates are in great demand, but it is difficult to install them yourself due to their complex design and high requirements for accuracy and adjustment.

What gates can you make yourself?

If you are an experienced builder, have access to the necessary equipment, components and assistants with the necessary skills, you can make any of the gates described above yourself. If you are an ordinary person whose talents and abilities lie in other areas and have minimal construction, plumbing and welding skills, then you can only create swing and sliding gates. We recommend making swing gates - despite serious shortcomings, they are easy to install, look beautiful, and finding materials for them is not difficult. Below we will describe the main stages of creating and installing swing and sliding gates; this will help you better understand the process, evaluate your strengths and create beautiful and functional gates yourself.

How to create and install swing gates

To create a gate with dimensions of 2.2x2.2 meters you will need:

steel profile (square) with a cross section of 30 mm, 20–30 meters;
steel profile (square) with a cross section of 100x100 mm or a steel pipe with a diameter of 100–120 mm, 6–7 meters (two sections of 3–3.5 meters each);
garage hinges 4–6 pieces;
door hinges 2 pieces;
door lock;
corrugated sheeting 6–7 square meters;
steel reinforcement with a diameter of 10–14 mm 3–6 meters;
manual or mechanized drill with a diameter of 300–400 mm;
manual tamper (you can use a log of suitable length and thickness), to which handles are attached for ease of use;
Bulgarian;
welding machine;
drill with a set of different drills;
self-tapping screws;
screwdriver;
roulette;
sharp core;
square;
plumb and level;
sand, crushed stone, cement and water;
shovels;
several assistants.

Creating sashes

When creating the sashes, you must determine in advance how they will be attached to the supports; their width depends on this. If from the inside, then the width will be equal to the width of the passage, if from the front (outside), then it will be equal to the width of the opening + double the width or diameter of the supports. It is also necessary to determine in advance whether you will cut a gate into one of the doors, because the location of the frame elements depends on this. After this, it is necessary to determine the number of vertical posts of the frame - in regions with weak winds on gates of this width, it is optimal to install 3 vertical posts on each leaf. If the winds blow strongly and often, then it is necessary to install 4 racks.

Mark the vertical and horizontal elements along the length and cut them using a grinder, then weld them from their frame. Be sure to use a square when marking, and also use it to check the shapes of the gates during welding, this will avoid skewing the gates and altering them. When the sashes are made, hang them on supports. Keep in mind that the strength of the gate will depend on the quality of the welds with which you connect the hinges to the supports and leaves. Some craftsmen who have to install gates in mountainous areas first mount the supports, and then make the doors for them and hang them. This approach allows you to adjust the gap between the gate leaves.

If you decide to make a gate with a wicket, then take into account the size and shape of the canopies, because the wicket should open and close freely, but there should not be large gaps between it and the frame of the door. You can hang the gate and install the lock both before and after hanging the gate.

Installation of supports

Using a drill, drill a hole for the supports. If there is no drill, you can dig it out with a shovel, but the diameter of the hole will be several times larger, which means you will have to either fill the support with stones or pour much more concrete. The depth of the holes for the supports should be 30 cm greater than their depth. This is necessary to create a sand-crushed stone cushion that will protect the gate from groundwater. This pillow must be thoroughly compacted with a tamper or log.

If it rains heavily in the fall in your region, and in winter the temperature drops below 15 degrees below zero, then the depth of the hole for the supports should be greater than the depth of soil freezing.

In addition, the hole must be made with a diameter of at least 40 cm and insulated at the level of freezing depth with polystyrene foam. You can also install (if free space allows) screw piles, which will act as supports. When installing supports, pay special attention to the distance between them and their verticality; for this, use a tape measure and a level or plumb line. Check with a level or plumb line from 2–3 sides. Having placed the supports, fix them and fill them with concrete. The gate can be hung after 20–25 days.

Hanging and plating

There are two technologies for hanging and covering gate leaves of this size - the first involves first lining, then hanging, the second, on the contrary, first hanging, then covering. The first technology is used when you can attract a sufficient number of assistants and lifting the doors is not difficult; the second is used if you are working together or even alone. Hanging the gate is done in the same way as ordinary doors or windows - the sash is raised, the canopy pin on the support and the hinge hole on the sash are aligned at the top and bottom, then lowered. This operation can be performed alone, but only on sashes without trim. At least 2 people (preferably 3) are required to hang cased sashes.

Cut the corrugated sheeting to the nearest millimeter, maintaining right angles, otherwise the entire structure will look clumsy and awkward. For fastening, use metal self-tapping screws; keep in mind that self-tapping screws are not bolts, so tightening too tightly will only lead to stripping of the thread.

Installation of latches and locks

There is no single standard for locks or latches for swing gates. Some limit themselves to a chain and padlock, others install a mortise lock or deadbolt, and still others install automatics. Therefore, experiment based on the materials available to you.

Swing gates are one of the most common, as their cost is much lower compared to sliding, sliding or lifting ones. They are quite easy to install and can be metal or wood. You can make them yourself if you strictly follow the directions, drawings and instructions, and also have the necessary materials and tools.

Swing gates: types and design features

Based on their design features, there are two-leaf and single-leaf gates. Often in garages, hangars and warehouses they use a combined version - with two doors and a gate. This significantly saves space and materials for creating a separate entrance.

Garages usually have gates with two leaves and a wicket.

In most cases, we find structures made of metal sheets or wooden picket fences, and only in some public places (hospitals, government organizations and institutions, schools, kindergartens, etc.) - forged, tubular or lattice. They can also be mechanical and automatic.

Metal gates can be made of corrugated sheets, aluminum (cheaper, but have a shorter service life) or steel sheets with a thickness of 1 to 5 mm. The latter are resistant to various damages, but are very heavy, so they require stronger support posts. Swing gates made of corrugated sheets are an excellent example of a reliable, durable and aesthetically attractive design that can be made in almost a few days from a minimal amount of material. The disadvantage of metal gates is their susceptibility to corrosion if not properly maintained.
Metal swing gates are durable and reliable, but are susceptible to corrosion
Wooden products are durable and reliable, and have a beautiful appearance. Their advantages are reasonable price and long service life, and disadvantages are a low degree of fire resistance and susceptibility to rotting.
Wooden swing gates look beautiful, but have a low degree of fire resistance
Very often you can find a combined option - steel supports with metal doors, covered with wooden boards, which also serve as an additional element of strength.
Automatic swing gates with an electric drive simplify the process of opening and closing them, since this does not have to be done manually. The principle of operation of the electric drive is the operation of a gearbox, which drives the lever that controls the swing gate. Typically, the automatic installation includes a signal light, an electrical unit, photocells and the lock itself.
Automatic swing gates are often made from corrugated sheets

Electric drives in automatic designs are divided into three types:

Lever. They are equipped with a curved lever that sets the doors in motion. This is a simple and inexpensive drive that meets all the requirements for strength and reliability. It allows you to open gates weighing about 1 ton.
Underground. They are quite difficult to install and subsequently maintain, so they are rarely used.
Linear. They give swing gates an aesthetic appearance due to the fact that the lever is tightly mounted to a metal or wooden leaf. They have a large power reserve, so they are more expensive than lever ones.

Swing gate device

The structure consists of a frame made of a round or square pipe of a certain diameter and cross-section and valves, each of which may contain:

The optimal gate width is 3 meters. This distance is sufficient for entry of any type of passenger car and even a truck. The height of the gate without taking into account the rise above the ground usually reaches 2 m.

Preparing for the construction of swing gates: drawings and sketches

You must first select a location for the swing gates and carry out some preparatory work:

clear the area;
remove trash;
if necessary, level the surface.

You will also need an accurate design drawing.

An accurate drawing of swing gates will help you calculate the required amount of material

What you will need for work: materials and tools

To build the frame of a double-leaf swing gate you will need:

metal profile with a cross section of 8x10 or 10x10 cm with a wall thickness of about 0.7 cm;
profile pipe 6x3x0.2 cm;
channel beam with walls 14–16 cm thick.

Corrugated sheets - light metal sheets coated with special compounds that can significantly extend the service life of the material and do not require additional processing or painting - are most often used to cover the frame of swing gate structures. There are several brands:

C is a durable and lightweight sheet, which is made of galvanized steel and has a low rib height;
NS - has a greater corrugation height and sheet height;
H - a heavy sheet that has a high level of strength and reliability, is used for cladding large structures.

Usually people buy profiled sheets of the C8 or C10 brand, since they are considered the lightest and most durable. The number here indicates the depth of the wave. Craftsmen recommend using a sheet with a thickness of 0.4 mm: this way the gate will weigh approximately 50 kilograms, and installation will not require large lifting devices and mechanisms.

The optimal type of profiled sheets for cladding swing gates is material grade C8 or C10

The work also requires roofing felt or other waterproofing material, concrete mortar and metal corners.

Material calculation

To determine the total length of the frame, perform the following steps:

multiply the width of one sash by 4;
multiply the height of the frame by 6;
find the sum of the obtained numbers.

We calculate the amount of metal profile as follows:

find the area of one sash (multiply its width by height);
multiply the resulting value by 2.

If you choose the standard width and height of the sash (2 m), then you will need 8 m 2: two sheets of 4 m 2 each to install two leaves.

The height of the support pillars should correspond to the height of the corrugated sheet, taking into account burial in the ground, and this is another plus of 50–70 centimeters.

Tools

To build swing gates you will need:

drill, bayonet and shovel;
drill;
electric screwdriver;
metal scissors;
square and level.

Step-by-step instructions for the manufacture and installation of gates

After clearing the space for installing the structure and preparing materials and tools, the main work can begin.

Mark the place for burying the support pillars, and then use a drill to make holes for their installation with a depth of approximately 1.2 m and a diameter of 0.5 m. If you don’t have a drill, you can use a shovel. The pillars must stand very firmly, since the reliability of future gates depends on this.
Clean the pipes, removing rust from them, treat them with an anti-corrosion agent and wrap the lower edge with roofing felt. This is necessary to protect parts from corrosion.
Place a layer of crushed stone about 15 cm thick at the bottom of each hole, install pipes and fill with concrete. Close the upper parts of each rack with special plugs to prevent water from getting inside.
Check the verticality of the supports using a level. To prevent the pillars from sagging, they can be supported with special beams. Wait until the concrete dries (3–5 days).
Assemble the frame on a special flat area.
Weld it and further strengthen it with steel corners.
Visually divide the long sides of the frame into 3 parts and weld jumpers - stiffening ribs - to conventional points. You can also weld the strips diagonally.
Weld the hinges to the places where the jumpers are attached.
Cover the frame with corrugated sheets, having previously cut out rectangular recesses for the hinges with a metal knife.
Recesses for loops on the corrugated sheet are cut with a metal knife
For fastening, use hex head screws, matched to the color of the base material.
Hex head screws are used to fasten the corrugated sheets.
It is better to weld the hinges when the frame is still on the site. To prevent the gate from being removed, weld additional mounting angles above the top.
Hang the gate on its hinges and place a wooden stand under the middle of the structure.

Electric drive for swing gates

You can also make this part yourself if you are knowledgeable about electricity. Its main part is a mechanism from a parabolic antenna with a worm gear. Old-style satellite TV has a rotating mechanism that can be installed on swing gates. The worm gear operates like a rotary mechanism, but can be operated on a low voltage of 36 volts. Factory drives only operate on 220 volt power.

For assembly you will need:

The device can be assembled in one day.

Installation of factory electric drive

If you prefer a more reliable system, it is better to use automatic factory units. But first you need to decide where the doors will open - inward or outward.

Drive Installation Tools:

electric drill;
pliers;
screwdriver;
roulette;
insulating tape;
hammer.

To select the type of device, you will need to measure the distance between the hinges and the inside of the support:

Next, we determine the width of the sash and also take into account the required wind load. The gate leaves must move easily so that the electric drive can open and close them smoothly. If the structure opens inward, any electric drives can be installed. For steel pillars it is best to take a linear or lever model, and for brick pillars - only the second. If the gate leaves open outward, then any system that is mounted inside the opening will do. It will take up about 15 centimeters of space on each side of the structure.

Operating procedure:

Weld metal reinforcements around the column when installing the electric drive on a brick pillar.
Set the hydraulic drive to manual mode and connect the fastening elements to the gate by welding.
If a linear model is selected, then after welding, leave at least 1 cm after the gate is fully opened for smooth and free movement. Check the movement of the valves and the clarity of the movement of the electric drive, and then install the stops and motors.
Install the strips, attach the remote controls and turn on the system. Then equip the automation with switches.
Install a warning light and a photographic device that cannot be equipped until all other systems have been adjusted.

After welding, all seams must be sanded well to remove scale and excess metal. It is better to treat the pillars and frame with a special anti-corrosion agent and paint them.

Bolts for swing gates

If you plan to install automatic gates, then complex locks and deadbolts will not be needed. But if you wish, you can install them. Vertical models are one of the most common, as they are easy to make with your own hands from ordinary fittings:

An overhead horizontal bolt is usually installed on swing gates made of corrugated sheets on the transverse strips of the frame.

Video: how to make an electric gate

You can build electric swing gates yourself. By following the instructions for mounting and covering the frame, installing an automatic system, the home owner will be able to install a reliable and durable structure on his site.

Gates made of corrugated sheets differ in the type of opening of the leaves and are divided into swing, sliding and lifting. We will consider the simplest option, which does not require much experience to produce. Do-it-yourself gates from corrugated sheets can be made with little material and labor costs, however, they will look stylish and beautiful if you choose the right color and design.

Installing corrugated gates with your own hands

Swing gates- the simplest and most common gate design used on private land. Gates made from corrugated sheets are easy to weld and install with your own hands, even with a minimum of tools and skills; you just need to strictly follow the instructions.

Standard swing gates consist of two supports and two leaves, which are connected to each other and closed with a lock, latch or other latch.

Gates made of corrugated sheets. Blueprints

To start making gates, you need to draw up blueprints gates made of corrugated sheets, calculate the amount of necessary materials, fasteners and choose the right tools. We will look at how gates are installed on a standard 4-meter driveway opening.

To weld the support posts for the gate you will need thick wall pipe 60x60x3x3000 mm. You can choose any pipe cross-section; it does not affect the quality of the supports and is selected only based on their availability.

For the gate frame you will need rectangular pipe 40x25x2x6000 mm. From it we make rectangular frames, to which corrugated sheeting will be attached in the future. After the frames are ready, they are attached to the gate hinges to the installed posts. A locking device is provided at the point where the valves close.

After installing the structure, you can begin painting the frame gate To do this, we clean the surfaces using a grinder, cover them with 2 layers of primer and paint of the same color as the selected corrugated sheet for cladding. The part of the pillars that will be underground must be coated with waterproofing paint to protect it from corrosion when in contact with wet ground.

Pillars installed in prepared, drilled holes in the ground and concreted with M200 or M250 concrete. The depth of the foundation for gates made of corrugated sheets must be at least 1.5 meters and a diameter of 25 cm. To avoid skewing of the gate after some time, you can additionally connect the pillars with a monolithic concrete crossbar.

After the concrete has dried, the frame of the gate frame is sewn up on the front side corrugated sheeting with an overlap equal to the width of one wave. This must be kept in mind when calculating the amount of materials needed. Roofing screws or steel rivets are used as fasteners to avoid corrosion at the point of contact of different metals.

Lastly, it is installed locking device. If necessary, apply paint to areas of the gate damaged during installation.

Do-it-yourself gates made of corrugated sheets. Video

A real example of making gates from corrugated sheets

Swing gates made of corrugated sheets are one of the least expensive and reliable solutions, which can also be easily implemented in a short time with your own hands. Making gates is a simple process that only requires careful study of the instructions and the necessary tools. Usually, in order not to take up extra space on the site when opening the gate, The doors are made to swing open towards the street.

To make swing gates from corrugated sheets with your own hands you need:

Decide on sizes designs and draw diagram installation of gates made of corrugated sheets. Standard openings for vehicle passage are usually 4 or 6 meters. In any case, you cannot make a gate narrower than 4 meters, since you need at least room for maneuver, and secondly, in the future, you may have to let a car much wider through the gate than you have now.

Do-it-yourself gates made from corrugated sheets. Drawing

On drawing you need to apply all the dimensions so as not to get confused during the manufacturing process and choose the right amount of materials. The heavier and more voluminous the structure, the larger the diameter you will need to select pipes for the gate frame. Internal jumpers can be made from a profile of smaller diameter, since the load on it is significantly lower than on external elements.

Drill holes in the ground, with a diameter slightly larger than the diameter of the support pillars. In order for the pillars to be securely fixed in the ground, the hole must be filled in crushed stone by 10 cm. It will act as a foundation cushion for gates made of corrugated sheets, level the gate posts and concrete. In order for the cement to set properly, you need to leave the structure alone for 6-7 days.

After the concrete has hardened, they are welded to the pillars. frame pipes fence After finishing work on the gate frame, they will be covered with corrugated sheets.

Do-it-yourself gates made of corrugated sheets step by step. Photo

Next, according to the drawing, it is manufactured rectangular frame for gates. At this stage, it is important to clearly mark and carefully weld each corner so that the gate does not have distortions or irregularities in the welding areas. Before final welding, you need to check how well the gate leaves fit together, after which the seams are welded and cleaned.

You can further strengthen the frame and give it even greater rigidity using metal corners. They are welded along the inner perimeter of the frame. After this, internal jumpers are welded to the frame, dividing the frame into equal rectangles. The lintels also strengthen the gates; in addition, sheets of corrugated sheets are attached to them.

The frame for wickets. If it is located next to the gate, then the width of the leaf is usually 80 cm, and the height corresponds to the height of the gate itself. Another option is when the gate is made inside one of the gate leaves, like a garage door. This gate is much smaller in size.

Gate installation begins with installation crossbars between support pillars. The crossbar is leveled, the gate is placed on it and checked level. To begin with, you need to secure the gate with a rope, slightly lifting the middle of the gate where the doors meet. The middle of the gate should be raised by a distance of about 3-5 cm. To fix the gate in this position, you can use a small board of appropriate height or other suitable object. After completion of the work, the force of gravity will act on the sashes in this place and they themselves will lower by this amount.

After the level is checked, we tack by welding loops to the posts, paying attention to the fact that some of the hinges with a pin are attached to the gate, and without it to the gate posts. The hinges must be welded flush with the profile, without protruding beyond it or falling through. At this stage, you need to carefully check how the gate opens and closes. After checking, it will be possible to finally weld the hinges, and to secure the gate from removal, a piece of corner is welded over the top of the hinge.

how to make a gate from corrugated sheets with your own hands. Photo

When the welding work is completed, the seams are finally cleaned, the frame is coated paint for protection against corrosion and rust. The support pillars are also coated with paint. Particular attention should be paid to the part that will be underground in order to protect the metal from destruction under the influence of the external environment.

For fastening corrugated sheets It is best to use roofing screws. The screw caps can easily be matched to the color of the corrugated sheet.

Sheets of corrugated sheets are cut to the shape of the gate, taking into account the overlap in one wave. From the outer edges we make slits for hinges, make preliminary markings and fasten the sheets, ensuring the accuracy of the work.

We install locks and latches.

This completes the manufacture and installation of gates from corrugated sheets with your own hands. If any parts of the gate are damaged during installation, it is necessary to re-paint the gate again to avoid corrosion of the metal during operation. After you tried to make your own gates yourself, you could be convinced that most of the costs in the manufacture of gates are labor costs, and the several hours spent on making gates more than pay off both in monetary terms and in the opportunity to create and make your own hand individual design for your gate.

Gate projects made from corrugated sheets

Even at the project stage, you can come up with a special design for the doors or columns and make minor changes to the drawings of gates made of corrugated sheets. The main thing is that the manufacturing process is virtually uncomplicated, but the end result is a much more interesting design of the passageway.

Swing gates made of red corrugated sheets are made with elements artistic forging. The posts with decorative tips and the uneven top edge make the gate look stylish and natural. They will suit a home in almost any style, except high-tech.

Double-leaf swing gates made of brown corrugated sheets with a black frame decorated decorative elements in the center of the valves and sharp tips along the upper edge. The gate is installed in a standard opening, the gate is cut into one of the leaves.

Sliding gates made of green corrugated board are in harmony with brick pillars and are made of the same material as the fence. A simple and stylish solution in this case provides reliable protection of the house from burglary and prying eyes.

Double-leaf swing gates are made in the same style as the fence. The gate is decorated with an element decorative forging. Brown corrugated sheeting in combination with brick supports is a classic solution that makes the fence not only reliable, but also beautiful.

Recoil gates made of corrugated sheets are a simple and reliable solution for protecting your site. On the street side, the gates are covered with corrugated sheeting, the color of which can be easily matched to the color of the fence or supports. If desired, an automatic system is installed on the gate, which will make opening and closing the gate even more convenient.