Ariston water heater (80 liters): characteristics of models and their main advantages. User manual (instruction) for the operation of the Ariston electric water heater Ariston water heater 65 liters instruction manual

The firm "Ariston" specializes in the production of water heating equipment. Water heater "Ariston" 80 liters (instruction attached to the device), as well as other models of devices are widely known to the inhabitants of our country. Each new model has a more stylish design and is produced using the latest technology.

Figure 1. Ariston water heater for 80 liters

Characteristics of water heaters

All models of water heaters of the company have a very long service life. This effect is achieved by coating the inner walls of the device with modern materials that protect the boiler from rust. Cold and hot water do not mix inside, so it is possible to constantly maintain the temperature of the liquid inside the unit. Built-in temperature sensors are designed to protect Ariston from overheating. At the moment of a sharp change in the mains voltage, a protective device is activated and disconnects the boiler from the network. A special thermal insulation layer that keeps the water hot saves electricity or gas.

Some models of heaters have protection against bacteria. Water in such devices is always clean. Sometimes it happens that there is no water in the plumbing system. In this case, the device cannot turn on. Again, a special protection system will not allow him to do this. Almost all models of the company, including Ariston 80, 100, 30 liters, are equipped with the functions listed above. The main differences between different models is only in the external design of the devices. The body can be flat, round, horizontal, vertical. Any of them fits perfectly into the interior of the room (Fig. No. 1). Internally, their device is exactly the same (Fig. No. 2):

internal boiler;
thermal insulation layer;
branch pipe for water inlet and outlet;
magnesium anode (Fig. No. 3);
thermostatic thermostat.

Figure 2. The device of the Ariston water heater for 80 liters.

A boiler is a tank for cold water. Outside, it is closed by an outer casing. The water entering the tank is heated by a built-in heating element. Sometimes there are 2 heating elements. This is if an electric water heater. Between the boiler and the outer casing there is a layer of thermal insulation. In general, the design resembles a thermos device. The water in it retains its temperature for a long time. It comes out through the outlet tube. Ariston 80 also has a magnesium anode. It is installed to prevent deposits of mineral salts on the inner walls of the tank. It should be changed as needed. You can see this when cleaning the heating elements (Fig. No. 4).

When the water is heated to the set temperature, the thermostat disconnects the device from the network. The operation of the unit is monitored using an indicator light. The built-in thermometer allows you to monitor changes in water temperature. This is how the Ariston 80, 50 liter, 100 liter and other models are arranged. Their operating instructions are the same for any model. Each instrument is supplied with an instruction manual. It must be carefully studied, then the device will work for many years.

Figure 3. Magnesium anode.

Purpose of water heaters

Installing a boiler in the house is carried out to provide the home with hot water. The heater can be selected in 100 liters, 80 or smaller sizes. All Ariston models have the same internal structure, therefore, the water heater connection diagram is the same for this series of devices. It is better to invite a specialist to install the device. If you decide to do it yourself, the work should be done according to the plan:

inspect the device from the outside;
prepare fasteners;
check grounding;
place the outlet correctly.

Figure 4. Cleaning the heating element of the Ariston water heater.

When inspecting the device, it is necessary to check the safety valve well. It should not have visible flaws. If they are found, the valve must be replaced. As fasteners, it is recommended to use plastic dowels and self-tapping screws for them. You need to connect a heater for 100 liters or any other to a separate power line. The outlet must be located in a dry place. The use of extension cords is prohibited.

Properly installed storage boilers start immediately after they are connected to the network. This is indicated by the illuminated indicators. The temperature of the water inside the device is also shown by thermometers.

Conclusion on the topic

There are many systems for providing hot water to private houses and country houses.

The most famous high quality devices are produced by Ariston.

There are many models, but they all have the same internal structure. Instructions for use of these devices is also the same for all brands. Storage devices for heating water differ only in external outlines. All characteristics of different models are also the same. Only the 80 liter model can still use the antibacterial function. To activate it, you just need to press the "power" button and hold it in this position for 5 seconds. The water temperature can be set between 30-75 °C.

Each time you turn it on, you need to control the water level in the boiler. When turning off the boiler for a long time, you need to drain all the water from it. Each device comes with a 1 to 2 year warranty. Repairs are made in almost every city with a warranty card.

For the convenience of quickly obtaining hot water in the room, regardless of central heating, storage electric water heaters - boilers were developed. The range of electric heaters is very wide. Today we will take a closer look at the instruction manual for one of them, namely, the Ariston water heater.

Your task is to use it correctly

Having purchased Ariston electrical equipment for the home, do not forget to carefully study the instructions and always have it "at hand". Follow instructions should not in any way be skeptical and underestimated, since it is, first of all, your safety. Even if you accidentally lost the instructions from the device, you can get its electronic version specifically for your Ariston model on the official website of the manufacturer. People who create electrical devices, check them, test them, put as much useful information in the manuals for use and operation with the only important goal - that you use them correctly. In the same article, general requirements and introductory points will be considered.

Boiler diagram Ariston 50

Boiler designs have approximately the same construction scheme. It has a body, a water tank (the boiler itself), and a heating element (otherwise a heating element, sometimes there are several of them in the configuration). Be sure to install a magnesium anode next to the heating element, which prevents the formation of scale. The boiler itself from the outside and in its inner part has an insulating layer.

Two pipes lead to the water heater - one for supplying hot water, the second for cold. Boiler bodies can be cylindrical or flat. The boiler tank can have a different capacity - from 30 to 100 liters. The basic principle of operation of the boiler is to heat the water in the tank and maintain its constant temperature, set by a person, depending on the need.

What you need to know about Ariston boilers

The main function of Ariston water heaters is to provide houses, apartments, cottages, cottages with hot water for household purposes. In order for the electric water heater to serve for a long time and with high quality, the following characteristics:

It should be noted that the instructions for water heater models that differ only in the system of different volumes of the same series are almost identical. There are two types of heaters according to the principle of operation: flow-through (the heat exchanger heats the temperature instantly as soon as you open the tap) and storage (water is drawn into the tank and then heated). Storage water heaters, or boilers, have compact tank, designed for different volumes - 30, 50, 80, 100 liters. Boilers are of direct heating (they themselves heat water using gas or electricity) and indirect (such devices are located near the heat exchanger, for example, a boiler).

Installation of the device must be carried out by a specialist, otherwise your equipment will lose the right to warranty service. After installing an electric water heater check the following:

About installing an electric water heater Ariston according to the instructions

Before installing the water heater, make sure the wiring can handle the added power. It is especially important that the outlet to which you are going to connect the device is grounded and not in contact with water. The power supply to the water heater must go from the shield on a separate cable. When choosing a place to install an electric water heater, consider its weight together with water in three times the size and the strength of the walls.

For fastening, hooks with a size of at least 15 mm are required. It is recommended to install a water heater in the immediate vicinity of the displacer, which will also reduce heat loss when water is supplied to the point of analysis. The distance from the ceiling is at least 10 cm, the space around the device is within a radius of at least 50 cm for technical work.

Under what conditions should the device not be installed?

If the water is hard, you must additionally install a filter, otherwise the water heater will quickly fail. It is impossible to install the device in rooms, the temperature regime of which may have a negative indicator, to exclude the influence of factors dangerous for the device - dampness, frost, direct sunlight, dust and insects. Maximum avoid splashing water, steam on the body of the device, that is, it is not recommended to install it directly above the bathtub.

With a weak water pressure, it is necessary to set the maximum temperature, otherwise the device may not turn on at all.

Only branded parts

All parts of the water heater, when first installed, must be in good condition. This is especially true for the safety valve. If damage is noticeable, the part should be replaced with a similar one. In no case do not use adapters or extension cords, do not replace the water heater plug with another one. Separate power line required to power the boiler. If the power cord is damaged, replace it with a similar one.

When turning off the electric heater, use a two-pole switch, the gap between open contacts is from 3 mm. Also note that the pipes to which the water heater pipes will be connected have withstood temperatures above 80 degrees Celsius and the maximum working pressure.

Precautionary measures

If you know that you will not be using the appliance for a while, simply drain all the water from it. To do this, turn off the power to the device, close the cold water supply valve at the water heater, and open the hot water tap on the mixer. Open the tee drain valve. A magnesium anode that wears out over time should be replaced with a similar one. The first start-up of the device should be carried out strictly according to the instructions.

Prevention

With frequent use of the boiler, the first technical inspection should be carried out in six months or a year. Every 3 months it is recommended to drain the contents of the tank in order to remove sediment, which prevents heat transfer and reduces the efficiency of the heating element. It is also recommended to replace the magnesium anode after a year of operation of the device. Never ignore the error codes that appear. You can see in detail what each of them means in the instruction manual.

The comfort of a modern apartment is impossible without warm water. But public utilities are in no hurry to make our lives easier and more enjoyable. Therefore, it is necessary to independently take care of the presence of comfort in your home. Hardware stores offer us a huge selection of water heaters. Which one to stop?

If your home is not adapted for the installation of gas water heaters, then opt for Ariston boilers of 80 liters. This is a well-known Italian brand that has become a leader in the design and manufacture of household appliances. In order to dispel your doubts, we will explain the boring instructions in an accessible language.

Features of the water heater

A characteristic feature of water heaters is built-in tank. Water accumulates in it, keeping the temperature set by the program. Such a model will become relevant for those who from time to time have problems with hot and cold water supply. The eighty-liter tank of the model, as the instructions indicate, is ideal for a family of three. Wash the dishes, take a shower, bathe the baby.

The structure of the boiler resembles a thermos: in it, the liquid not only heats up, but also retains heat. The heat-insulating material occupies the empty space between the body of the water heater and the tank. Schematic representation The manual clearly shows this to us. Thanks to him, energy is saved: after all, you do not have to constantly maintain the temperature.

The internal tank of the Ariston water heater of 80 liters is made of high-quality steel, which has increased resistance to corrosion processes. The fact is that under the influence of aggressive environments (constant high temperatures, humidity, changes in water level), metal components suffer first of all. Therefore, the Ariston engineering bureau developed a special alloy, which received maximum resistance to rust corrosion.

The heating element of the water heater (TEN) has a reliable insulation. The feature of the model is heating element material - alloy, which may contain:

copper;
stainless steel.

Thermal power is increased by a brass flange.

One of the main parts of the Ariston boiler 80 liters is a magnesium anode. It is made of a special alloy and is attached next to the heating element. Its function is to protect the walls of the water heater tank from rust, to reduce the amount of scale. If you do not start fighting corrosion in time, then over time it will begin to corrode the metal walls of the container and, as a result, it will begin to let water through. Scale layers on the heating element will increase the heating time, which will lead to waste of electricity, and even breakage of the element. Entering into a chemical reaction with an aggressive environment, the anode protects internal parts from negative influences. Of course, you will not read this in the instructions for the device, but it is useful for obtaining general information.

Intelligent control system in which even a schoolboy will understand. The ergonomic design allows you to place the Ariston 80 liter water heater models in a horizontal position. In addition, the equipment is reliably protected from overheating, high pressure.

Water heater installation

So you bought a boiler and carefully study the instructions. Remember that in order for the water heater to work reliably, all installation actions should be entrusted to the service center employees. In the event of an error during self-installation, the warranty does not apply to the equipment.

Water heater: control system

Before turning on the water heater, you must make sure that there is water in the tank.

When the boiler is connected to the network, within one or two seconds, the temperature readings will be displayed on the screen of the water heater control panel. The instruction indicates that if the numbers flash, then this means only one thing - the device is still turned off. Click on the "On / Off" button (in the upper left corner) to start the technique.

There is a power control button on the remote control. It can be used to adjust the strength voltage from 2500 W to 1500. This function allows you to increase or decrease the time for heating water.

The temperature setting is activated by holding the button (plus or minus) for a few seconds. The range ranges from 30C to 75C. After installation, the water heater remembers the program, working in the specified mode. The instruction says: if the device is turned off, all settings are reset.

If you have not read the instructions to the end, then you do not know about the very convenient function of the water heater - protection against bacteria. Hot water is an ideal breeding ground for all kinds of microorganisms. And heat kills them. By enabling this option, you force the technician to increase the degree above 65, that is, to a level where microbes cannot exist, multiply. Once a month is enough for your water heater tank to be freed from all evil spirits.

Possible breakdowns

Water heaters "Ariston" 80 liters belong to the technique with a high degree of reliability. However, as sad as it is to say, damage does happen.

According to the repair service employees, the most “popular” breakdown is the failure of the electronic scoreboard. Do not panic, flipping nervously through the instructions, this does not affect the overall operation of the water heater. Experts also recommend using not the maximum temperature, but within 60C.

Heating elements for boilers "Ariston" 80 liters need to be changed from time to time. No matter how powerful anti-scale protection is, the quality of our water still does not improve. Therefore, after two or three years, your heating element will turn into a small pebble. If you do not open the water heater, then you can determine the presence of this unpleasant feature by increasing the heating time.

The instructions for the water heater indicate the marking commonly reported errors:

E2 - an attempt to turn on the boiler with an empty tank;
E3 - the temperature sensor is depressurized, a short circuit has occurred;
E4 - in case of heating water up to 90C.

If you see any of the above on the water heater control panel, you need to contact the service center.

So, we examined the main characteristics of one of the popular models that Ariston water heaters represent 80 liters. With proper operation, compliance with all the rules of the instructions, this reliable device will serve you for many years. And a wide network of official service centers will nullify discomfort in the event of a breakdown.

Convenient connection of water-heating equipment from the company "Ariston" consists in the use of manufacturers of an autoclave special flange mechanism. The basic principle of operation of such a mechanism is based on pressing the gasket under the influence of water pressure. As a result, it is possible to completely eliminate not only the leakage of liquid, but also the formation of watery smudges. To avoid unnecessary heat losses, the fixing of electrical models of the water heater from the company "Ariston" is carried out in close proximity to the output point.

Water heater for a shower in the country houseHeating water in the pool

Water connection

Next comes the connection to the water supply. A scheme is thought out, first drawn on a piece of paper, and then transferred to the walls with real dimensions. Along the lines where the pipes will pass, holes are drilled and clips are installed.

We close the valve at the water inlet, install a tee on the branch closest to the boiler. From it is a pipe to the water heater. A valve is installed on it so that it is convenient to repair the device, a strainer and a check valve.

We lead a flexible hose to the boiler and connect it to the pipe. Usually the input is marked in blue. In the same way, we draw a branch to the watershed point. It is not advised to connect without flexible hoses. On the one hand, it looks better and more reliable, but if there are sudden pressure drops, the tank takes the whole blow.

The inlet to the boiler is marked in blue

After connecting all the nodes, the valves open and all connections are checked for leaks. If they are found, reconnections are made or more tow is added to the threads.

Description of anode rods

The magnesium rod eliminates corrosion of the inner walls of the tank, and also softens the scale that forms on the heating element during the operation of the water heater. It is a magnesium alloy rod on a metal threaded stud and is screwed to the heating element flange, together with which it is inserted inside the water heater tank. The hole thread diameter ranges from M4 to M8 depending on the size and weight of the magnesium alloy on the stud. The larger the size and weight, the thicker the magnesium anode stud. The diameter of the magnesium anode is from 14 to 25 mm. The length of the magnesium part without the stud is from 140 to 660 mm.

Operating principle

The water entering the water heater contains soluble calcium and magnesium bicarbonates, which are present in it in the form of Mg2+, Ca2+, HCO3- ions. Magnesium is the first to react with water, since it is more active than iron and binds free oxygen formed during heating due to a multiple increase in the amount of Mg2+ cations. When the anode is installed in the tank, not hard scale (CaCO3) is formed, but soft scale (MgCO3 or Mg(OH)3), which is easier to remove when cleaning the water heater, or which itself falls to the bottom of the tank during the operation of the water heater due to thermal expansion or contraction of the heating metal element. The anode will dissolve over time, so it is advisable to check or replace the magnesium anode once a year or follow the water heater manufacturer's instructions.

Is it necessary to install a magnesium anode in a water heater?

Modern boilers have tanks made of stainless steel, with titanium, glass-porcelain, enamel coating. In this case, the tank corrodes at the welds and begins to leak over time, so it is necessary to regularly replace the magnesium anode. If it was not originally in the water heater, then it must be installed in the case when scale forms on the heater. In this case, the manufacturer most likely performed welding using a special technology or even made the tank one-piece, without welds. Without an anode, hard scale is formed, which has a lower thermal conductivity. This increases the heating time and the amount of energy consumed, reduces the efficiency, there is a constant overheating of the metal of the heating element. In the end, this leads to its rupture and failure. Therefore, timely and regular replacement of the anode will allow your water heater to work for many years.

What to look for when choosing a magnesium anode?

The main selection criterion is the diameter of the thread on the stud so that the anode can be fixed on the heating element flange or nearby, if such mounting is provided. The second criterion is the length, since meter ones, for example, simply may not fit. The next criterion is thickness. Anodes with a large diameter can touch the heater tubes, although in this case the plate with the mounting hole can be bent. The next criterion is the length of the stud. This choice is rare, as certain electric heaters require a long stud to keep the heating tubes out of the way.

thread diameter on the stud;
length;
thickness or diameter;
threaded stud length.

Prices for the main models name, description, manufacturer, price

When it comes time to buy a heating device, it is immediately better to pay attention to the Ariston 80 liter water heater, the price of which is fully consistent with the quality. Consider some models of heaters from this manufacturer.
.
ARISTON ABS BLU R - vertical storage water heater

The price ranges from 6300 to 7700 rubles.

ARISTON ABS BLU R – vertical storage water heater. The price ranges from 6300 to 7700 rubles.

It has an anti-corrosion coating Ag +;
Additional protection in the form of a magnesium anode;
Uniform heating of water is provided by the Nanomix technology;
Thanks to Absolut Bodyguard System technology, the system is blocked in the event of a lack of water or power surges;
Built-in safety valve.
Built-in external thermometer.
Mechanical control with indicator.
Water heating up to 75o is carried out in 3 hours with a consumption of 1.5 kW.

Boiler ARISTON BLU R - Photo 12

Ariston vls pw 80

water heater ariston vls pw 80 – wall-mounted heater with the possibility of mounting horizontally and vertically. The price for this model varies between 11,000 - 13,000 rubles.

The inner tank is treated with a special Ag+ coating;
Double heating element accelerates water heating by 60% after connecting the ExraPower mode;
ABS 2.0 protection protects the system from power surges and operation in the absence by turning it off.
External water temperature sensors allow you to monitor the state of water heating;
Built-in ECO antibacterial system;
The Nanomix technology accelerates the heating of water, which contributes to the uniform heating of the liquid.
Water is heated up to a maximum value of 80o at a power of 1.5 kW in 3 hours, at a power of 2.5 kW in 2 hours.

Water heater functions

Ariston SUPER SGA

Ariston SUPER SGA – excellent gas heater made in Italy. The price of such a storage water heater is 16,500 rubles.

Device characteristics:

Steel case;
Internal enamel anti-corrosion coating;
Thermal insulation layer made of polyurethane foam;
The presence of a gas valve.
Connection can be carried out both in parallel and in series;
Works independently of the mains;
Ability to control the flame;
External regulators and indicators.

Flat electric water heater Ariston ABS VLS INOX PW Can be installed in vertical and horizontal position. The price for such a model is 17,250 - 19,930 rubles.

Main characteristics of this model:

Steel inner tank with additional protection;
The “fast” function speeds up the heating process by turning on the second heating element;
Antibacterial protection system;
Protection against overheating, power surges, switching on without water;
Built-in “Nanomix” system;
The presence of an electronic thermometer;
There is a system "Autodiagnostics";
External display with control buttons.
Water heating is carried out to a temperature of 80o by one heating element in 3 hours 06 minutes with a consumption of 1.5 kW, with the “fast” system turned on in 1 hour 51 minutes with a consumption of 2.5 kW.

Advantages of Ariston technology

Like all Ariston appliances, the water heaters of this company have a lot of benefits:

The first of these can be called stylish design which helps to decorate any interior. Moreover, each of the models is created in accordance with the latest technologies.
Ariston 80 water heater is different longest service life . This effect was achieved due to the fact that the internal walls of the storage tank are covered with a layer of modern material that protects the tank from plaque and rust.
Built-in latest dividers, prevent mixing of already heated and cold water . This allows you to keep the temperature of the liquid. Also, the Ariston heater is protected from overheating, thanks to built-in temperature control sensors.
Presence of a safety shutdown device , which is triggered at moments of a sharp change in voltage.
Using Ariston water heaters, users can significant savings on gas or electricity consumption . This is facilitated by the presence of thermal insulation, which keeps the water hot for a long period of time.
Many models of water heaters equipped with bacteria protection which makes it possible to use purified water. If there is no water in the system, then you do not have to worry that the water heater will turn on, as it is equipped with special protection.

Repair

If we break down the repair actions of the units into several stages, they will be as follows:

It is necessary to diagnose the type of failure.
Determine the fault
Replace the failed assembly or part.

Features of water heaters "Ariston"

We are considering the repair of the Ariston electric boiler. Models from 50 to 100 liters. One of the advantages of the models of this company is the use of a classic autoclave flange. This solution does not allow water to flow through the gasket. The gasket is pressed against the pressure of the water in the water heater. The larger it is, the greater the tightness. But Chinese manufacturers have learned to fake this gasket, therefore, when purchasing it as a replacement, you need to look for a “native” one, avoiding fakes.

Boiler "Ariston"

The next feature is that the heating element is equipped with an elongated knife contact, so heating elements from other manufacturers are not suitable.

The water heater is supplied with a magnesium anode.

Examination

Before starting the repair of Ariston water heaters, you need to check whether there is electricity in the house and whether the water has been turned off. Often this factor misleads inexperienced users.

The next step is to check the correct connection to the mains and cold water. If these positions are maintained correctly, then the problems should be sought in the following:

The circuit breaker is off.
The automatic safety device has been activated.
The heating element burned out.
Electronics broke.

Replacing the heating element

If you find out that the heating element has burned out, then it needs to be replaced. Try to repair the Ariston water heater with your own hands.

Self repair

For this you need:

Disconnect the boiler from the power and water supply.
Unscrew the two screws and remove the protective box.
Turn off the power that is directly connected to the heater.
After unscrewing two more screws, remove the cover of the water heater.
Remove temperature sensor and thermostat.
Remove the non-return valve from the water supply pipe and drain the water from the boiler.
Unscrew the fixing nut with an adjustable wrench and remove the fastening on the bar to which the flange is attached.
Move the heating element inward, unfold and pull out. Do this carefully so as not to damage the flange. Don't forget to put a container under the flange, as water will still flow.
Replace the heating element or clean the flange and tank from dirt. It is not recommended to remove scale from the walls, as this is an additional protection of the tank from corrosion. Remove only the scale that has crumbled inside or is easily cleaned with a rag.
Replace or clean the magnesium anode. It spins next to the shade.
Replace all parts in reverse order.

At the end of the assembly, check the tank for leakage. If it leaks, replace the gasket.

When replacing the flange, it is important to put the same design as it was. Otherwise, the gasket may break, and the boiler will start to flow.

A heating element

If you do not regularly clean the water heaters, then the anode and the heating element will collapse, despite the good adaptation of Ariston products to our water. Therefore, it is so important to regularly inspect and repair the Ariston boiler, you can do it yourself.

Fake Parts

Connecting the boiler Ariston

It is better if this work is carried out by specialists. The rules to be followed when installing the device are given below:

It is necessary to inspect the safety valve, which should not have visible flaws. If they are, then the damaged part should be replaced.
Plastic dowels are used for driving screws.
Be sure to check all grounding elements.
The electric heater requires a separate power line to operate. The use of extension cords is strictly prohibited. The socket is placed in a non-humid place.
In operation, you must use the plug that came with the kit.

The water heater Ariston 80 performs the following functions :

Turn on/off . After switching on, the whole system starts up, which is due to the lights on, the temperature of the water in the boiler will be displayed. If the indicators are not displayed or flashing, this indicates a system shutdown.
Water heater ariston abs vls 80 has power level adjustment function , which makes it possible to set the necessary indicators.
Water heater ariston abs vls pw 80 allows you to use antibacterial function , which can be activated or deactivated by holding the "power" button for 5 seconds.
Possibility to adjust the temperature using the "+" or "-" buttons in the range from 30o to 75o; The set values are not fixed. After switching on again, the values \u200b\u200bmust be set again. Standard temperature values are 75 °, power - 1500 watts.

Water heating

Depending on the volume of the tank, the time of the first heating will differ. It takes about an hour to heat 30 liters of water to 65 degrees, 50 liters two hours, and 80 liters three hours. Also, the time depends on the heat of the incoming water and the power of the apparatus. In winter, the water comes in cold and it will take longer to warm up.

Boilers with more powerful heating elements spend less time and more electricity on primary heating. For example, Ariston Platinum SI 80 H with a volume of 80 liters and a heating element of 1.5 kW heats water from 20 to 65 degrees in 3 hours and 6 minutes.

For two people, a volume of 30 liters is enough, fifty is enough for a family of 3 people. An eighty-liter model should be enough for 4-5 people living in the room where the water heater is installed. Also, the consumption largely depends on the habits and purposes of using hot water.

The system for using the heater is very simple and straightforward.

The device may only be installed by qualified personnel. Before installing the tank, it is necessary to check the serviceability of the electrical wiring. Specialists must make sure that the voltage in the network corresponds to the permissible voltage for the tank, specified in the instructions for use of the device. The use of adapters or extensions is excluded. It is not allowed to connect additional electrical appliances to the same electrical line. The outlet must be dry and away from water sources. If the power cord becomes damaged over time, it can only be replaced by a specialist.

So, the tank is already connected, how now to turn on the Ariston water heater ?. Instructions for use will help you connect the heater.

First you need to turn off the hot water supply in the apartment. Otherwise, the contents of the boiler will flow into the riser. Despite the presence of a non-return valve, turn off the water.

Open the faucet, wait until the water has completely drained. When the liquid stops flowing, close the valve.

See also: How exactly does an instantaneous water heater work?

Cold water and heated water enter the boiler and back through two pipes. On the tank, they are marked with a blue and red label, respectively. These mixers on both pipes must be opened. First turn on cold water, then hot. If you forget to turn on the hot water faucet, it will flow through the riser to the whole house.

When the air comes out of the device, and the liquid flows in an even stream, the boiler can be connected to the power supply and the desired program can be selected. Do not block the cold water pipe, the supply to the boiler is regulated automatically.

After five minutes, check the water in the tap, its temperature should increase. If so, then you did everything right.

There are also compact water heaters. Mounting such devices will not be difficult. They are installed in place of the old crane. After installation, the tank must be connected to a pipe through which cold water flows. Then turn off the hot water faucet and plug the appliance into the outlet. Turn on the water and you're done. To install such heaters, it is still better to contact specialists.

Any heating tank must be connected to a separate outlet, which is removed from sources of moisture.

When the boiler is finished using, it must be turned off. How to do it? Unplug the cord from the tank. Wait for the water in the tank to cool down. Close both taps, one of which supplies water to the tank, and the second releases hot water. After that, open the hot water riser.

If the boiler is used from time to time, then it is not necessary to drain the water from it. Water contributes to the fact that the parts in the device are less corroded. Drain the water just before using it again. When you do this, rinse, dial clean.

If a situation arises when the boiler needs to be emptied of liquid, then this can be done using the check valve installed on the device.

Be careful! When the tank is empty, its inclusion is strictly prohibited!

In order for the Ariston water heater to serve you for a long time, it needs care. Every six months it should be cleaned to protect the heating element from breakage. Any malfunction is best repaired by specialists.

To notice this, pay attention to the following:

water heats up noticeably longer;
hissing is heard during operation of the device;
the heater turns on and off more often.

With proper operation and timely care, the unit will last a long time, since Ariston uses only original spare parts for its devices. Heating elements are made of high-quality copper, a special system protects the device from overheating and freezing. Models are characterized by a flat shape, easy installation. Tanks are produced in volumes of 30, 50, 80 and 100 liters. The devices have a water purification system from bacteria. The displays are functional and easy to use.

Do-it-yourself Ariston boiler repair

Repair work related to the elimination of breakdowns in gas appliances requires the involvement of qualified specialists, and the repair of an electric boiler can be done independently.

Major mechanical failures are most often manifested by tank leaks., from which water begins to ooze or drip during operation. The cause of this problem may be corrosion in the areas of the welds or a malfunction of the reverse protection system of the valve, which operates and performs an emergency reset. In this case, it is necessary to eliminate the excess level of water and air pressure by means of a reducer. Any depressurization of the storage tank will require the purchase of a new tank. If such a defect is insignificant, then it is enough to replace the sealing gasket.

A fairly inexpensive measure is the independent replacement of some electrical parts, including a heating element, a bimetallic thermostat, sensors or switches. In case of prolonged heating, noise or hissing, as well as in case of activation of the ABS system shutdown protection, the replacement of the heating element is required, the average service life of which does not exceed five years. Replacement is carried out after de-energizing the device, draining the water and removing the flange.

It is very important to systematically check the magnesium anode, which is a consumable material and is designed to effectively protect the inner surface of the tank and the heating element from corrosive changes. When the anode is thinned by ½ of the original volume, a mandatory replacement is carried out

The heating element is able to last much longer if the so-called “dry” heating element is installed in the structure.

Installation

Do-it-yourself Ariston is a simple matter if you carefully read the instructions and follow its instructions. Of course, you can invite specialists who will do everything quickly and efficiently. The only “but” is the price of this service. For example, in Moscow it is from $100. Meanwhile, having minimal skills in working with plumbing, you can cope with this task in just 2-3 hours. Assuming you spend some money on consumables, the net savings is approximately $60.

Water heater connection diagram.

Evaluating the pros and cons, consider the risk of flooding the neighbors from below, if something goes wrong, measure your strength. The advantages of self-solving this problem include:

saving time and money;
acquisition of skills that you will need in the process of operating the water heater.

Access to the storage water heater (boiler) must be absolutely free, and the wall for fastening must be strong, capable of withstanding double the weight (with a unit capacity of 50 liters, calculate the load of 100 kg). Determine the condition of your electrical wiring: is it capable of handling a significant additional load? For example, for a water heater of 2000 W, there should be a copper wire cross section of 2.5 mm². Keep in mind that if there are old water pipes in the apartment, sometimes you have to replace them first and only then connect the boiler. Find out how much current your electricity meter is designed for. If less than 40 A, you will have to replace it.

Back to index

Inclusion

If you are turning on the boiler for the first time, you should do the following:

We examine the inlet pipes to the water heater and find the check valve. If the normal pressure is exceeded, water will pour out of it. Therefore, you should either substitute a small container under it, or connect and bring the tube into the sewer.
We collect a tank. We open the valves at the inlet and outlet of water from the device. To do this, turn the handle of the taps 90 degrees counterclockwise. Open the hot water faucet. We are waiting for the container to be filled. If water starts to flow, this means that the Ariston boiler is full.
It is advisable to visually inspect the pipes for leaks. If water drips somewhere, it is necessary to turn off the water and call specialists to fix the breakdown.
We turn on the device in the network. To do this, either insert the plug into the socket, or turn on the machine to which the electric cable is connected. The machine may be located near the installation site or in a switchboard.
Set the desired water temperature. It is recommended to set the level of 60-65 degrees. At higher temperatures, scale actively accumulates, and at lower temperatures, harmful bacteria can begin to multiply.
The temperature can be set with a mechanical knob, as in the Ariston SG 30 OR model, or with buttons on the control panel, as in the Ariston VELIS EVO PW model.

After that, it remains to wait until the liquid heats up and start using hot water. For convenience, you can mix cold tap water with warm water from the boiler to achieve the desired temperature.

Water heater Ariston

It is very important to prepare in advance all the tools and consumables for the work. Before starting installation, make sure you have the following tools: .

Tools for mounting storage water heater.

roulette;
perforator with a drill;
wrench;
spanners;
wire cutters;
pliers;
two types of screwdrivers.

Consumables:

Unipack type paste or FUM tape;
tow;
3 stopcocks;
3 tees;
2 connecting flexible hoses (if not included);
metal-plastic pipe of the required length.
if it is necessary to replace the wiring - a three-wire wire, a socket or an automatic machine.

To install a storage electric heater, you will need an auto switch for 32-40 A, a PVA cable 3X6 -3X8.

Back to index

Installation

Installation of the water heater "Ariston can" is done by hand.

Installation of the Ariston water heater must be carried out in strict accordance with the instructions.

Installation instructions for the Ariston water heater, of course, are included with the purchase of the unit.

It is necessary to check the outlet and test the voltage in the electrical network. The socket must be grounded and have a separate wire from the shield.

Fastening

Since the weight of the device will be quite heavy due to the large amount of water, the wall on which it will be installed must be strong. The bolts with which this structure will be attached must also be strong. It is better to use metal fasteners: hooks, bolts, screws, with a diameter of 10mm. The connection of the Ariston water heater should be close to the place of hot water supply so that there is no unnecessary heat loss. It is necessary to clearly mark the place of attachment of the water heater using a level and a tape measure. Make sure that the load is evenly distributed, there are no distortions. Using a drill, holes are drilled in the wall, to which brackets and holders are attached, on which the boiler is hung.

Some models are installed on the floor. In this case, the symmetrical installation is adjusted by the feet of the appliance.

Connection to the water supply system

The hoses and other connecting elements used for connection must withstand the design pressure and temperature of about 80 degrees. When connecting to a water supply system, it is best not to connect two different metals to each other, such as copper and steel (in pipes). To do this, you need to use a dielectric adapter.

With the help of a valve included in the device, a pipe for cold water is connected. The hot water pipe is connected using a pipe. Your task is not to confuse these two inputs when connecting the Ariston boiler.

Start installation with a cold water pipe, it is marked in blue. A sealing tape or tow is wound on the pipe. If you take tow, then it must be lubricated with a special paste. Then the tee is screwed on. There will be a relief valve at the bottom of the tee. It is installed in an upward direction. This valve will control pressure and superheat. On the side of the tee we put an emergency drain valve. You will use it if you need to completely drain the water from the boiler.

The shut-off valve is placed at the bottom and the boiler is connected to the water supply through an adapter.

Also, through a shut-off tap and an adapter, a connection to hot water is made.

The correct scheme for connecting the Ariston water heater to the water supply is shown in the video:

Electrical connection

Only after the connection to the water is made, we connect it to the electrical wiring. Since this unit consumes a lot of electricity, the wires must also meet the requirements.

Connecting the Ariston water heater to the mains is as follows:

Disconnect the water heater from the electrical network.
The power supply wires are connected to the screw terminals of the thermostat.
Be sure to observe the phases when connecting: - L, A or P1 - phase wire; N, B or P2 - neutral wire.
Connect the ground wire to the clamp on the boiler body.
Connect the test lamp terminals to the terminals.
Press the thermostat button.
close lid
Before switching on the power supply, it is necessary to check the filling of the boiler with water.
Turn on power.

Scheme for connecting the Ariston boiler to electricity through a double circuit breaker:

Boiler connection

The electric wire for the boiler must pass through the wall or be hidden in a corrugation made of non-combustible material. The connection cable must be three-core, preferably copper. Installation of the Ariston water heater must provide for grounding. Grounding is not done on metal objects and pipes, such as sewers, plumbing, and so on.

Beginning of work

Before starting work, you should once again make sure that the flange is exactly in the center. If it is slightly off to the side, install it correctly (loose or tighten). After filling the tank with cold water, open the hot water outlet cock on the boiler to allow excess air to escape, then close it.

When you turn on the heating pressure on the body of the water heater, the lamp should light up. Sometimes during operation, the cold water hose heats up. In some Ariston models, the temperature can be adjusted with a special knob connected to the thermostat with a screw. Economy mode is marked on the unit with the letter "E".

In the event of an unexpected breakdown or malfunction of the new water heater, you can contact the warranty repair shop in your city. The usual warranty period for the Ariston boiler is 1-2 years, depending on the model (the same as for the Termex, Bosch or Nova Tek water heater). If before the expiration of this time you tried to open and repair the unit yourself, then most likely you will be denied free warranty service. Keep the warranty card issued by the store until the end of the warranty period.

The storage water heater from the company "Ariston" - the unit is quite simple to operate and reliable. If you strictly follow the instructions during installation and with further use, it will serve you faithfully for more than one year.

Boiler installation

Accumulative water heaters heat water for a certain time in special tanks from 10 to 150 liters and more. In small city apartments, most often they put boilers of 50 or 80 liters. Fastening to a fragile wall (for example, drywall) is excluded. There is no fundamental difference in installing a small or large tank, except that the larger the unit, the more powerful the fastening elements.

Scheme of the storage water heater.

Break the work into several stages. The main and most important stage is fixing the boiler to the wall. If the container is horizontal, it is advisable to attach it higher, under the ceiling, if it is vertical - at the level of the person's head or chest. Under the boiler, the floors must be waterproofed in case of leakage.

You need to work carefully, avoiding scratches and damage to the outer surface of the unit from tools. It must also be borne in mind that the electronic control unit of the boiler does not have an independent power supply, in case of any power failure, the settings will fail and a restart will be required.

Use bolts, hooks, screws with a diameter of at least 10 mm. Using a tape measure, mark the level of the attachment points. Make sure that all points on the back of the unit provided for installation are engaged, do not skew. Drill holes with a drill, then attach brackets and holders to them, on which the boiler is hung.

Like all Ariston appliances, the water heaters of this company have a lot of benefits:

The first of these can be called stylish design which helps to decorate any interior. Moreover, each of the models is created in accordance with the latest technologies.
Ariston 80 water heater is different longest service life . This effect was achieved due to the fact that the internal walls of the storage tank are covered with a layer of modern material that protects the tank from plaque and rust.
Built-in latest dividers, prevent mixing of already heated and cold water . This allows you to keep the temperature of the liquid. Also, the Ariston heater is protected from overheating, thanks to built-in temperature control sensors.
Presence of a safety shutdown device , which is triggered at moments of a sharp change in voltage.
Using Ariston water heaters, users can significant savings on gas or electricity consumption . This is facilitated by the presence of thermal insulation, which keeps the water hot for a long period of time.
Many models of water heaters equipped with bacteria protection which makes it possible to use purified water. If there is no water in the system, then you do not have to worry that the water heater will turn on, as it is equipped with special protection.

The device of ARISTON water heaters for 80 liters

The external simplicity of any water heater carries with it the same uncomplicated internal structure. The difference can be observed only in the external design and materials from which the heater is made. The external structure of the housing can be made in a cylindrical or flat shape.

Any water heater has:

Inner tank - a boiler into which cold water enters. It is framed by an outer casing.
The water that entered the tank is heated by the built-in heating element . For faster heating of water, two heating elements may be present in the boiler.

Thermal insulation layer , which is present between the body and the boiler, acts as a thermos, which allows you to keep the water temperature longer.
Water enters the tank through shortened branch pipe with divider . The heated water is supplied by a drain pipe.
magnesium anode , built into the ariston 80 water heater, helps prevent the deposition of mineral salts on the walls of the inside of the tank. This element is replaced as needed.

During heating, when the set temperature is reached, the thermostat , which automatically interrupts the power circuit.
If the heating element is turned on, and the water temperature indicators have fallen below the set ones, then the configured thermal relay .
Allows you to control the operation of the water heater voltage indicator (indicator light).
Built-in thermometer makes it possible to monitor temperature changes.

The storage water heater ariston 80, which belongs to flat horizontal models, has the same typical internal structure.

Shuttle Ariston electric water heater: instructions for using boilers, diagram

After buying such an assistant as an Ariston 80 liter water heater into the house, the instruction should be the first document that should be carefully studied before starting its operation. This will help to understand all the nuances of working with the boiler and extend the period of operation of the device.

Ariston water heater 80 liters is used to supply the house with hot water. The choice of this series of heaters is promoted by a set of positive characteristics.

The ariston 80 v water heater has the same device and instructions for use as all models of this series. Installation should be carried out in accordance with the attached diagrams.

Connecting the boiler Ariston

It is better if this work is carried out by specialists. The rules to be followed when installing the device are given below:

It is necessary to inspect the safety valve, which should not have visible flaws. If they are, then the damaged part should be replaced.
Plastic dowels are used for driving screws.
Be sure to check all grounding elements.
The electric heater requires a separate power line to operate. The use of extension cords is strictly prohibited. The socket is placed in a non-humid place.
In operation, you must use the plug that came with the kit.

The water heater Ariston 80 performs the following functions :

Turn on/off . After switching on, the whole system starts up, which is due to the lights on, the temperature of the water in the boiler will be displayed. If the indicators are not displayed or flashing, this indicates a system shutdown.
Water heater ariston abs vls 80 has power level adjustment function , which makes it possible to set the necessary indicators.
Water heater ariston abs vls pw 80 allows you to use antibacterial function , which can be activated or deactivated by holding the "power" button for 5 seconds.
Possibility to adjust the temperature using the "+" or "-" buttons in the range from 30 o to 75 o; The set values are not fixed. After switching on again, the values \u200b\u200bmust be set again. Standard temperature values are 75 °, power - 1500 watts.

Water heater operating rules

It is not difficult to extend the life of an ariston brand storage heater, you just need to install it according to the instructions and steadily follow the rules for using the device :

Should control the presence of water in the boiler every time you turn it on and off devices. Switching on is possible only when the tank is filled with water.
If the power cord is damaged, replacement must be carried out with a material of the same brand , which is best purchased at a specialized outlet.
If the heater will not be used for a long period, especially during the cold season, then water from the boiler must be drained , following all the rules prescribed in the instructions. After that, the cold water supply valve is closed. After these steps, the heater is disconnected from the electricity supply.
The heater eventually requires cleaning from dirt . To carry out this work, it is better to use the services of specialists.

Reviews of ARISTON water heaters with a volume of 80 liters

For those buyers who have decided and purchased an ariston water heater, the reviews remain purely positive. Below are some of them.

“Pros: excellent “employee”.
Cons: didn't find any.

Since we have a private house, but there is no gas, it was decided to purchase a boiler. Tired of constantly heating water on the stove in order to buy up and simply wash the dishes. We asked friends who already have experience with such units. Those, in turn, advised the ariston water heater. After reading more reviews, we opted for a brand like ARISTON.

Bought a model with a volume of 80 liters. This is enough for a family to use. I really liked the presence of a sensor with which you can always find out the level of water temperature in order to “not get into a slippage”)). This heater served us for many years, it was even sad to leave (they removed it, because they had gas and connected a double-circuit boiler). But during the service, this heater proved to be just fine: it quickly “delivered” hot water and kept its temperature for a long time, it consumed little electric energy. In general, the model is excellent !!!

“Advantages: compactness, fast heating of water, low electricity consumption, equipped with additional protection.
Cons: none.

Excellent water heater. I had to get acquainted with him when a systematic shutdown of hot water began in the houses for an indefinite period. In order not to sit and wait for a "miracle", it was decided to buy a water heater. On the advice of the seller purchased a heater

Ariston SG-80, which did not have a high price. And yes, we liked it too. The place for the boiler was determined in the toilet, where it did not create inconvenience to anyone. During the use, we made sure that we took an excellent assistant: it quickly heats water (80 liters in 4 hours), consumes little - 1.5 kW, heats water to an acceptable temperature - 75 o, there is a safety valve and a magnesium anode. We were completely satisfied with our choice!”

“Advantages: simplicity, reliability, ease of use.
Cons: didn't find any.

The Ariston SG-80 brand water heater came into our house back in 2013, we bought it at a discount and did not regret it. My husband did the installation himself and it wasn't that hard. The heater serves the bathroom and sink. There is enough water to the head, despite the fact that we set the heating level to 50 o, it allows you to save a little. It takes an average of 2 hours to heat 80 liters at this temperature. I was very pleased with the quiet operation of this device. We are satisfied with the purchase."

“Advantages: heating up to 75 °, low consumption of electricity.
Disadvantages: little essential, but ill-conceived lid.

Our small town is not connected to hot water supply. While they lived together, they managed. But after the appearance of the baby, they decided to buy a boiler. We chose models with a volume of 80 liters available at our means. We settled on the Ariston SG 80 model, which suited us in all respects: energy consumption of 1.5 kW, volume, heating temperature, which reaches 75 ° and, of course, the price.

Having established, they themselves felt the dignity. Everything worked "with a bang." It created a little inconvenience when switching the temperature, when it was necessary to switch the lever under the lid. It was not entirely convenient to crawl with a screwdriver to the right place. But this is not so significant, because we had to change the temperature indicators only once. In general, the model is excellent. I recommend to all!"

Prices for the main models (name, description, manufacturer, price)

ARISTON ABS BLU R - vertical storage water heater. The price ranges from 6300 to 7700 rubles.

It has an anti-corrosion coating Ag +;
Additional protection in the form of a magnesium anode;
Uniform heating of water is provided by the Nanomix technology;
Thanks to Absolut Bodyguard System technology, the system is blocked in the event of a lack of water or power surges;
Built-in safety valve.
Built-in external thermometer.
Mechanical control with indicator.
Water heating up to 75 ° is carried out in 3 hours with a consumption of 1.5 kW.

water heater ariston vls pw 80 - wall heater with the possibility of mounting horizontally and vertically. The price for this model varies between 11,000 - 13,000 rubles.

The inner tank is treated with a special Ag+ coating;
Double heating element accelerates water heating by 60% after connecting the ExraPower mode;
ABS 2.0 protection protects the system from power surges and operation in the absence by turning it off.
External water temperature sensors allow you to monitor the state of water heating;
Built-in ECO antibacterial system;
The Nanomix technology accelerates the heating of water, which contributes to the uniform heating of the liquid.
Water is heated up to a maximum value of 80 °C at a power of 1.5 kW in 3 hours, at a power of 2.5 kW in 2 hours.

Ariston SUPER SGA - excellent gas heater made in Italy. The price of such a storage water heater is 16,500 rubles.

Device characteristics:

Steel case;
Internal enamel anti-corrosion coating;
Thermal insulation layer made of polyurethane foam;
The presence of a gas valve.
Connection can be carried out both in parallel and in series;
Works independently of the mains;
Ability to control the flame;
External regulators and indicators.

Flat electric water heater Ariston ABS VLS INOX PW Can be installed in vertical and horizontal position. The price for such a model is 17,250 - 19,930 rubles.

Main characteristics of this model:

Steel inner tank with additional protection;
The “fast” function speeds up the heating process by turning on the second heating element;
Antibacterial protection system;
Protection against overheating, power surges, switching on without water;
Built-in “Nanomix” system;
The presence of an electronic thermometer;
There is a system "Autodiagnostics";
External display with control buttons.
Water is heated up to a temperature of 80 ° C by one heating element in 3 hours 06 minutes with a consumption of 1.5 kW, with the “fast” system turned on in 1 hour 51 minutes with a consumption of 2.5 kW.