CONTRACT OFFER

Individual entrepreneur Klimov Alexander Nikolaevich, acting on the basis of the Certificate of state registration an individual as an individual entrepreneur, hereinafter referred to as the Seller, publishes this Public Offer on the Digital Goods presented on the Seller's website

1. GENERAL PROVISIONS. SUBJECT OF THE CONTRACT

1.1. In accordance with Article 437 of the Civil Code Russian Federation(Civil Code of the Russian Federation), this document is a public offer, and if the conditions set out below are accepted, the individual accepting this offer pays for the Goods and / or Services in accordance with the terms of this Agreement. In accordance with paragraph 3 of Article 438 of the Civil Code of the Russian Federation, payment for the Goods by the Buyer is an acceptance of the offer, which is considered equivalent to the conclusion of the Agreement on the conditions set forth in this offer.

1.2. Based on the foregoing, carefully read the text of the public offer, and if you do not agree with any clause of this offer, you are invited to refuse to purchase the Goods and / or Services provided by the Seller.

1.3. In this offer, unless the context otherwise requires, the following terms have the following meanings:

Acceptance - full acceptance by the Buyer of the terms of the Agreement;

Offer - a public offer of the Seller, addressed to any individual (citizen), to conclude a contract of sale (hereinafter referred to as the "Agreement") with him on the existing conditions contained in the Agreement.

The Buyer - a visitor to the Site - an individual who has entered into an Agreement with the Seller on the terms contained in the Agreement and makes the purchase of a Digital Good (s) and / or services.

Parties - the Seller and the Buyer referred to together.

Site - a site hosted on the Internet with the domain name "site", which is an online store containing an assortment of goods and services of the Seller.

Digital goods - a virtual product that is the subject of this agreement and has the following types:

a) finished digital goods - digital goods laid out for sale, having a finished look and ready for use.

b) courses - training programs using a distance learning system.

Delivery - delivery by the Seller of digital goods presented on the Site via electronic communication channels to an electronic mailbox, the address of which is indicated by the Buyer in the Order;

Account - a virtual "office" of the Buyer, in which the registered user sees his personal data.

Registration is the process of entering personal data by the Buyer into a special form on the Site when placing an Order (last name, first name, email address).

Order - individual items from the assortment list of Digital Goods specified by the Buyer when placing an application for a Digital Good.

2. SUBJECT OF THE CONTRACT

2.1. The Seller sells Digital Goods in accordance with the current price list published in the Seller's online store on the website, and the Buyer makes payment and accepts the Goods in accordance with the terms of this Agreement.

2.2. The Seller delivers the Digital Goods in a purely virtual form, through Email and does not ship printed goods by mail.

2.3. This Agreement is an official document of the Seller.

3. ORDERING

3.1. The order of the Goods is carried out by the Buyer by sending a properly completed form in the process of processing the payment. All columns of the form for payment must be completed. In the absence of the necessary information to identify the Buyer and send him the Goods, the Order will not be accepted by the Seller.

3.2. When placing an Order, the Buyer undertakes to provide the following information about himself:

last name and first name,
E-mail address.

3.3. The Buyer agrees to the processing by the Seller of the Buyer's personal data with or without the use of automation tools. This consent of the Buyer applies to his last name, first name and other information related to his personality and specified when placing the Order. Consent is provided for any actions in relation to personal data that are necessary for the proper execution of this Agreement, including without limitation: collection, systematization, accumulation, storage, clarification, use, distribution, blocking and destruction, as well as any other actions with personal data in accordance with the current legislation of the Russian Federation.

3.4. Payment by the Buyer of the Order made on the website means the Buyer's consent to the terms of this Agreement. The day of payment for the Order is the date of conclusion of the Agreement purchase and sale between the Seller and the Buyer.

3.5. If the Buyer has any questions regarding the Goods, before placing the Order, he must seek the advice of the Seller by e-mail [email protected] site, or through the feedback form posted on the site.

4. CONDITIONS AND TERMS OF DELIVERY OF DIGITAL GOODS

4.1. Delivery of the paid goods to the Buyer is carried out by sending an e-mail with a link to receive the Digital Goods to the e-mail address that the Buyer indicated during the Registration process. The term for sending a letter is 8 hours from the moment of receipt of payment.

4.2. The Seller delivers the Goods on the basis of the Order placed by the Buyer.

4.4. The Goods are considered received by the Buyer, and the Seller's obligation to deliver the Goods is fulfilled from the moment of fixing the operation for sending the Goods via electronic communication channels to the Buyer's electronic mailbox in the Seller's automated electronic system.

4.5. In case of non-receipt of the Goods by the Buyer within the period specified in clauses 4.1 and 4.2. of this Agreement, or due to technical problems of the mail server of the Buyer's provider or for other reasons that have arisen, the Buyer must contact the Seller and report the non-receipt of the Goods. In this case, the Seller will re-deliver the Goods free of charge within 2 (two) business days from the date of receipt of the relevant message from the Buyer.

5. PRICES AND PAYMENT PROCEDURES

5.1. The range and price of Digital Goods are freely available on the Seller's Website.

5.2. The cost of the Goods indicated on the website may be changed by the Seller unilaterally at any time.

5.3. Payment for Digital Goods is made in a non-cash way using payment system installed on the seller's website.

5.4. The Buyer's obligation to pay for the Goods is considered fulfilled from the moment the funds are received on the Seller's settlement account

6. SPECIFICATIONS FOR DIGITAL GOODS

6.1. Digital goods are supplied in the following formats: PDF format, JPG format, mp4 format, XLS format.

7. RIGHTS AND OBLIGATIONS OF THE PARTIES

7.1. Rights and obligations of the Buyer:

7.1.1. The Buyer has the right to provide him with the Digital Goods in accordance with the technical characteristics indicated in this Agreement (clause 6)

7.1.2. The Buyer is obliged to pay for the Digital Good in full before receiving the Digital Good.

7.1.3. Goods purchased from the Seller are for the personal use of the Buyer. The Buyer undertakes not to distribute copies of the Digital Goods in any form or by any means.

7.2. Rights and obligations of the Seller:

7.2.1. The Seller has the right not to deliver the Digital Goods for which he has not received the funds in full.

7.2.2. The Seller is obliged to deliver the Digital Goods in the proper quality in accordance with the technical specifications indicated in this Agreement (clause 4).

8. RESPONSIBILITY OF THE PARTIES

8.1. For non-fulfillment or improper fulfillment of obligations under this agreement, the Parties shall be liable in accordance with the current legislation of the Russian Federation.

8.2. The Seller is responsible for the conformity of the delivered Digital Goods technical specifications indicated in clause 4, as well as for the compliance of the content of the Digital Good with all the norms of the law.

8.3. The Buyer is responsible for the proper use of the Digital Good in accordance with clause 7.1.3

8.4. The Seller is not responsible for the content and accuracy of the information provided by the Buyer when placing an Order.

8.5. The Buyer is responsible for the accuracy of the information provided when placing the Order.

SELLER'S DETAILS

IP Klimov Alexander Nikolaevich

OGRNIP 311222511700014

website privacy policy website

This site is an information and educational Internet project of Klimov Alexander Nikolaevich (IP Klimov Alexander Nikolaevich. OGRNIP 311222511700014).

This site strictly adheres to the following privacy policy:

1. Subscription to the newsletter is carried out at their own discretion by anyone through the form on this site. For this, your email address is requested. You must also confirm your consent to receive the information materials of the site, in the letter that comes after filling out the form.

2. The personal data of each subscriber is used only to send him periodic newsletters, news and project promotions: and will never be transferred to third parties in any form.

3. To get an idea about the content of the newsletter releases, you can read the content of the “blog” section of the site:

4. Each subscriber can at any time unsubscribe from receiving mailing lists by clicking on the link at the end of each letter.

Reading time ≈ 4 minutes

A circular saw is used to cut wood and plastic. Its cutting base is a flat metal disk with a serrated outer edge. Choosing such a tool, everyone decides for himself what kind he needs: desktop, manual, stationary. Many prefer the manual option. However, in some situations it is necessary to fix the saw. In this case, you can make a table for a circular saw with your own hands, having the opportunity, if necessary, to fix the tool.

Preparation of tools and materials

Having decided to make a table for a manual circular saw on your own, you need to take care of the availability of all the materials necessary for work:

• laminated plywood (9 or 11 mm), size 800 mm by 800 mm;
• Chipboard 16 mm or other sheet material suitable for the manufacture of the body, sheet size 400 by 784 mm - 4 pieces;
• bars 40 by 40 mm (length depends on installation method);
• self-tapping screws;
• bolts.

For such a table, any hand-held circular saw will do. At the same time, it must be remembered that when attached to the table, the depth of cut decreases by 10-20 mm. So saws with small discs are not suitable for such a table.

Step-by-step instructions for assembling a table for a circular saw

1. Manufacturing of the case. Sheet material for the body is cut to size: 400 mm by 800 mm. Parts are fastened with screws and bars. It is better to assemble by pre-drilling the outer parts of the box. The result is a rectangular box without a bottom and a lid. top the bars are subsequently used to secure the plywood sheet.

2. Preparing and fixing the plywood top. Hole cut. First, a piece of 800 mm by 80 mm is cut out of a sheet of plywood. Next, measure the support shoe of the saw that will be mounted on the table top. On the reverse side plywood markup. You will need 2 center axles. Without them, you cannot perform accurate markup. Then marks are applied to the plywood corresponding to the dimensions of the support shoe. Then they make such measurements that the circular has: the diameter of the lower protective casing, its thickness, the maximum distance from the edges of the support shoe. In accordance with the dimensions obtained, marks are placed and a rectangular hole is cut out with a jigsaw.

3. Fastening the saw to the plywood tabletop. First, 4 holes are made in the shoe. Diameter - 10 mm. Next, install the tool so that the working part goes into the sawn hole. When the saw is leveled, mark the location of the holes. Marks are made in the central part. In order for the tool to stand securely, ploughshare bolts with a countersunk conical head (M8) will be needed for fastening. To install them, you will have to take care of the high-quality deepening of the cap, it can protrude by a maximum of 1 mm in an open form.

Plywood is drilled from the outside, the diameter of the holes obtained should be 8 mm, and then a countersink should be made under the cap. When the holes are ready, the saw itself is installed on the saw table for the circular saw, the bolts are tightened from the inside using nuts with plastic growers or spring washers.

4. Fastening the tabletop to the body. Start button. First, holes are made at a distance of 30 mm in the corners of the plywood tabletop. Then a hole is drilled in the central part of the bars. The parts are connected using a 18 mm M8 steel fitting. On the side part, a regular "Start - start" button is installed. An electrical network is laid inside the case, and the button on the tool itself is clamped.

5. Making a thrust beam. A simple table for a circular saw will become much more convenient if you equip it with a thrust beam. The drawings contain all the required dimensions. The beam can be made of plywood, and secured with full extension furniture rails. The resulting beam should slide over the surface at an angle of 90° to the cutting plane with little clearance.

6. An emphasis for longitudinal cuts. It is made from an aluminum cornice. At 150 mm from the edges, holes for the bolts are first drilled, and then 2 lines are drawn from the place where the bolts are attached to the center line. At the intersection and further towards the bolts at a distance of 30 mm, holes of 12 mm are made. Bolts from below are tightened with nuts. And along the drawn lines, cuts are made to the tonic, their width can be seen in the photo.

For those people who often do carpentry work for themselves or to order, it is simply necessary to have a stationary circular saw in their carpentry workshop. It is very convenient to work on a stationary machine and, again, the position of the back is straight, which is important during long and monotonous work.

Today, there is a large selection of machines and tools in stores, but a simple carpenter cannot afford a pair and you have to get out of the situation using natural ingenuity. For example, the master made a stationary saw from a hand-held circular saw, how did he do it? We look further.

materials
1. hand saw
2. plywood 11 mm
3. M-8 bolts with a furniture cap
4. screws
5. switch
6. wire
7. timber 40x40
8. furniture guides

Tools
1. jigsaw
2. hand saw
3. drill
4. screwdriver
5. hammer
6. screwdriver
7. pliers
8. ruler

The process of creating a stationary circular saw.
And as mentioned above, the author made his circular saw from a manual circular saw, and no changes were made to the design of the saw. Here, a table is simply made, and the sole of the saw is attached to the underside of the tabletop, where a cut was previously made under the disc, holes were first drilled and then sawn. A base is created from plywood and timber 40x40.

Then the tabletop is cut out of plywood, the author recommends using laminated or varnished, because the surface is even and smooth. As agreed, a cut is made, holes are drilled in the corners for subsequent fastening.

A circular saw is attached to the underside of the table top, using M-8 bolts, mainly the bolt heads should be drowned in plywood.

The switch is installed and connected, the start button on the saw is fixed in the pressed position, and the switch is connected to the outlet, so the saw does not need to be disassembled and something connected to it.

Also, for the convenience of conducting work, a mobile emphasis was placed on furniture guides.

The longitudinal emphasis is made of an aluminum corner.

To adjust it, you need to loosen the bolts and move it to the distance necessary for subsequent work.

But as you understand, with this installation of the saw, 10-20 mm will be lost.

And actually such a saw turned out from the author.

There is also a video for your attention from which you will learn a lot more. Happy viewing!

This concludes the story. Thank you for your attention! Come visit more often, do not miss the news in the world

Content:

In a well-equipped carpentry workshop, equipped in a country house or in a private house, a circular disk mechanism is required to process wood blanks.

Very often used as household woodworking equipment homemade machine, made on the basis of a hand-held circular saw or a cutting tool with an independent electric drive.

To accommodate any of these mechanisms, a specially equipped table with a surface that provides the convenience of working with wood blanks is required.

Depending on the type of cutting tool, as well as on the material used for the manufacture of the bed, the table for a circular saw can have the following designs:

• firstly, it can be made in the form of a workbench with legs and a hand-held circular saw fixed to it (lightweight version);
• secondly, it can be a structure equipped with a cutting disc, mounted on a metal frame. The drive part of such a machine, consisting of an electric motor and control circuits, is located in the lower part of the bed (capital option).

Making a table for a circular saw is quite within the power of every craftsman

Design choice

Before you make a table for a circular saw with your own hands, first of all, you need to decide on its design. So, a lightweight version based on plywood and beams should contain the following mandatory elements:

tabletop directly;
plywood body;
support legs for good stability
The structure of the capital structure should include the following nodes:

frame based on metal profiles or corners;
upper and lower brackets, necessary to accommodate the cutting blade with a shaft and drive equipment, respectively;
the table itself with a slot for the cutting blade, mounted directly on the metal frame.
The most affordable for manufacturing at home is a wooden table for a circular saw (i.e., lightweight design).

A lighter version of a table for a circular saw will look something like this

Preparation of sketch, material and tool

As an example, consider the procedure for manufacturing a wooden workbench with a height of approximately 100 - 120 cm. Before making such a table with your own hands, it is advisable to prepare a small sketch that will display the device of the future design, indicating the dimensions of its main elements.

The exact setting of the table height is made taking into account the growth of the master working on the machine (the location of the working plane at the level of the human hips is considered comfortable).

On the preparatory stage you should also decide on the material for the manufacture of the future structure, which, as a rule, is made of beams and plywood with a thickness of 28 mm.
In order to make such a table with your own hands, you will need the following blanks:

• metal sheet of suitable size;
• standard sheet of thick plywood;
• a metal square pipe from which the guides are made;
• a set of clamps in the amount of two pieces.

To assemble the table, you also need a tool kit from the following items:

• screwdriver and electric drill;
• electric jigsaw or ordinary wood saw;
• square, tape measure, ruler (for current measurements);
• manual frezer

Video: Making a table for a circular saw

Making a table cover

The procedure for manufacturing this structural element involves the following operations:

Work begins with marking and cutting out a plywood blank, the dimensions of which must correspond to the dimensions of the prepared iron sheet.

After adjusting to size, the surface of the workpiece is carefully polished with an emery cloth.

Then, on the lower surface of the plywood sheet, points of fixation of the actuator are marked with simultaneous marking of the slot for the cutting disc.

To do this, first try on the sole of the circular saw used at the installation site. In this case, it is most convenient to simply remove the disk from it and determine the exact location of the landing points.

Before installing it at the place of attachment, an additional check is made for the correct marking of the slot for the cutting disc.

The marking of the table top is done directly on the sole of the circular saw

At the final stage, the working surface is closed with a steel sheet with two guides, which is then fixed with ordinary self-tapping screws.

Subsequently, special markings can be made along the guides from the corners, which increases the convenience of processing wood material.

Additional information: In addition to plywood, plexiglass or fiberglass can be used to equip the operating surface of the table.

Assembling the frame with legs

The base or frame of the table is assembled from a set of transverse and longitudinal wooden beams, which are attached from the bottom of its cover, increasing the rigidity of the entire structure as a whole. For this, four bars with a section of 50x50 mm are quite enough, placed with an indent from the edge of the table of about 7-9 cm.
They are fixed on the bottom of the lid with suitable-sized screws in increments of approximately 23-25 ​​cm. On its front side, the fasteners are sunk into the material that completely hides their caps.
The frame can be made stronger by pre-treatment of the joint surface of the bars with a layer of wood glue, which is carried out immediately before they are fastened. After connecting the blanks smeared with glue, the latter are securely fixed with clamps, which are removed immediately after the adhesive has dried. The legs of the structure can be made from bars of the same section as the blanks for the frame (50x50 mm).

The design of the table must be strong and rigid.

The shape of the legs is selected based on the fact that they provide the maximum support area for the frame part of the base and have a shape that tapers towards the flooring. On one of these legs, subsequently, controls are placed to turn the saw on and off, duplicating the buttons located on its body.

You will be able to additionally increase the rigidity and stability of the entire structure with the help of a set of steel angles mounted in the area of ​​its butt joints. To fix them, it is recommended to use standard bolts with washers, which are preferably installed with their heads outward.

Features of the manufacture of a metal frame (bed)

The upper part of the metal base is a welded frame 800x800 mm in size with legs welded at the corners from pipes 220 mm long and with a cross section of approximately 17-20 mm.

On the frame of 25 mm corners, two longitudinal profiles are attached, used to install the shaft on bearings.

To ensure greater structural stability, the lower part of the frame is welded from larger corners (40 mm) and has two jumpers designed for mounting an electric motor with starting equipment circuits. At its corners, pipes are also welded, having the same length as on the upper frame, but somewhat larger in diameter (23-25 ​​mm).

Closer to the edge of such legs, threaded holes are prepared from pipes, in which special holders are located (they are also called “lambs”). With the help of these winglets, it will be possible to fix the position of the pipes of the upper part of the frame, which is moved in order to regulate the tension of the drive belt.

Functional expansion

In conclusion, let's touch on the topic of expanding the functionality of your working structure. If there is free space on the operating surface, additional woodworking equipment can be mounted ( electric planer or a cutter, for example). The presence of a planer and a wood router will allow you to expand functionality machine and turn it into a full-fledged woodworking center.

In addition to this, such a router can be equipped with a special mechanism for adjusting the position of its working part, which can be changed within specified limits (the so-called elevator).

Video: Saw table dimensions