How to remove protective glass from iPhone? how to remove screen protector from phone how to change screen protector on iphone 6
The display is the most fragile and weak point of the iPhone 6. Especially in view of the significantly increased dimensions and smoothness, it always strives to slip out of your hands. And then how lucky. Practice shows that luck is far from always, and the frequency of requests for repairs is proof of this.
Depending on the degree of damage, different repair methods are selected. An iPhone display replacement will be needed if it stops responding to commands, spots, stripes or streaks of the image appear. In this case, the matrix is probably damaged, and it cannot be repaired - you just have to install a new screen.
But if the monitor works, and the glass only cracked (as it often happens - they put it in the back pocket of jeans and sat down), then a simple replacement of the broken glass with a whole one is enough. And we do not recommend to postpone for a long time. Sharp edges and fragments inevitably scratch the matrix, it becomes unusable, and then - see above.
In principle, due to design features, glass replacement in the iPhone 6 involves the installation of an entire display unit in the assembly. As a rule, this option is much more expensive - due to the high cost of the original spare part. And also plus the work of the service department ... In order to save at least a little on repairs, we suggest you try to do it yourself.
Replacing the display on the iPhone
In order to change the glass on an iPhone, you will have to partially disassemble its case. Before starting disassembly, do not forget to turn off your smartphone. Find two sockets with "star-shaped" pentalobe screws near the lightning connector.
Unscrew them with a special pentagonal screwdriver - designed for ø 3.6 mm.
After unscrewing the screws, you need to start slowly removing the display cover. In order not to damage the seal between the glass and the body, prying it with hard objects, it is better to use a conventional suction cup with a gripping ring. Place it just above the Home button, and pull slightly.
Just slightly, since the cover, in addition to screws, is also held by a number of latches located around the perimeter. Gently pull them back, starting from where you just removed the fasteners and moving further as you open the case.
If you don’t have a suction cup (but we strongly recommend purchasing one, after all), then you can try to use a wide adhesive tape. It will be much easier to wipe off traces of the adhesive coating of adhesive tape than to restore damaged seals after a barbaric rough disassembly. Moreover, after such a procedure, you can forget about the vaunted tightness of the case.
Opening the top panel vertically, you will see wire connecting loops located in the area of the camera. It is they who interfere with the final removal, so you have to disconnect them from the system part of the device. However, access to their connectors is blocked by a protective metal bar.
You can get to the junctions of the cables with the board by removing the five fixing screws from the protective panel. Don't be alarmed - they have different diameters - that's how it was intended (don't forget this later when assembling).
Unscrewing them - remove the safety cover.
And now we have a "sandwich" of trails in all its glory. We begin, one by one, to disconnect them from the motherboard.
First, the camera cables are removed, then the speaker and the Home buttons, the last are the cables for connecting the display.
Try to do everything very carefully so as not to loosen the connectors and not reduce the sensitivity of the plugs. In the future, this is fraught with all sorts of interruptions in work or even serious damage.
Done - now the display can be easily detached.
Next, you need to remove the auditory speaker and front camera, as well as the Home button, from the dismantled non-working top panel. Since they do not come with a new display part.
We do everything according to the same principle - first we remove the metal mounting panels - by unscrewing the screws, and then we disconnect the cables.
This is what the shield above the camera with the speaker looks like.
And so - connecting loops, carefully turn them off.
In the photo below - "Home" - the actions are similar: unscrew, remove the shield, disconnect the cable from the board.
Since the “Home” button, for better tightness, has factory sizing, in order to remove it without damage, warm up the case a little. Without special tools, this can be done over an ordinary light bulb, for example.
And finally, unscrewing the fixing screws on the temples around the perimeter, remove the metal plate that protects the display from the inside.
Everything, with half of the work we successfully coped. Then, after printing the original new display, reassemble the entire structure in reverse order. Especially carefully check the reliability of all cable connections with the board. This is how iPhone glass is usually replaced. There is nothing complicated.
If you are not sure that you will remember the location of all the elements to be disassembled and the order in which they are disconnected, then we advise you to photograph all the actions taken in stages. This minimizes the risk of finding “extra” parts after the iPhone glass replacement is completed. In order not to get confused and not to lose tiny screws, put them in separate trays.
Is it possible to replace only the glass ourselves?
If, after damage, the display matrix continues to work, and the image it produces is of good quality, then it will be enough to install a new glass. Replacing the iPhone 6 glass will be much cheaper than reinstalling the entire unit. Even taking into account the work of an experienced master - a professional.
In principle, an independent iPhone glass replacement at home, without a special set of tools and equipment, is hardly possible. Since it is very firmly glued, and you can’t just manually detach it. You will need a separator to warm up the display, a remover for the factory adhesive coating, new glass, fishing line, special glue and a UV lamp to fix and polymerize it. And they are not cheap, and it makes no sense to buy everything for the sake of a one-time procedure.
Protective glass on "apple" gadgets is designed to protect devices from damage. A high-strength chemical composition is usually used to protect the display from chips and scratches. Some users neglect such protection, but in vain. Protective glass for iPhone 6 and other gadgets can significantly extend the life of your mobile device.
In this article, we will look at how to remove the protective glass from the iPhone 5 and devices of other versions. We will also pay attention to how to glue the protective glass on the iPhone. In addition, we will try to identify the advantages of this method of protecting the display over conventional film.
How to change and how to glue the glass - read the detailed instructions below.
If we compare the 2 main ways to protect the iPhone display screen - glass and film - most of the criteria will be in favor of the first.
The advantages of glass coating are:
- Increased strength with a small thickness of only 0.25 mm.
- The presence of an oleophobic coating that prevents the appearance of fingerprints on the display.
- Sometimes - the presence of a nano-coating, which gives an increased smoothness of the surface.
- Reliable fastening with silicone elements that do not allow the coating to move and prevent the formation of bumps and bubbles.
Flexible glasses to protect the display of mobile gadgets can also have hemmed edges. This means that the edges are rounded, so the coating is almost invisible. In addition, if the device is hit against something, the coating will not crumble. So if you are wondering what is the best protective glass - stop your choice on the element with hemmed edges.
Removing glass: precautions
Before you get started, you need to consider some rules. First, remember that the glass is quite strong on the display as it is very smooth. But the element is held not thanks to glue, but with the help of electrostatic forces. Thus, two perfectly flat surfaces are in close contact, and the glass cannot be removed simply by picking it with your finger. But it is also impossible to use a household object for this purpose, for example, a knife, since there is a risk of damaging the screen or case.
A silicone suction cup will not help in this situation either. If you stick this tool to a damaged coating, a void will form under it, and when pressed, it will slide off.
And if the mount is good, the suction cup will not go anywhere, but another problem will arise. The fact is that the sensor is attached to the body of the gadget using either glue or adhesive tape. The strength of these substances in terms of rupture is much lower than that of glass or a touchscreen. Therefore, strong pressure can lead to a complete breakdown of the display module and damage to its cables. You need to work carefully and carefully here.
How to remove protective glass from iPhone 5S, 4S
Even taking into account the fact that the period of operation of protective glass is longer than films, it also needs to be changed sometimes. The glass is on a silicone substrate, so it adheres firmly to the display. It takes some skill to remove it.
Before removing the protective element, you need to carefully prepare and purchase some tools and materials, namely:
- Spatula (or thin plastic card), mediator.
- Silicone suction cup.
- Lint-free napkin.
- Glass cleaner containing alcohol.
- Gloves.
Sometimes it happens that all the tools and materials listed above come with a new protective glass. But this happens quite rarely.
And the glass removal algorithm itself includes the following steps:
1 Wash your hands well with soap and water before starting work, and then dry them. You can not do this, but just wear gloves. This is to prevent fingerprints or streaks from appearing on the display. 2 If the glass is damaged, you need to choose the area that is best preserved, and on which there are no chips. In this place you need to attach the suction cup, pressing it firmly. 3 In the corner to which the suction cup is attached, you need to attach a mediator or a spatula, and pry it off. The edge of the coating should peel off. To do this, you will need to pull the suction cup towards you a little, but not much. To keep the screen from breaking. So we will achieve the goal so that a small distance forms between the screen and the glass. But if you do not have a suction cup, just insert the pick deeper. 4 In the course of glass peeling, deepen the tool. And if the display is large, you can use 2 mediators or spatulas for the procedure, moving them in different directions. 5 And the last step - we pull the suction cup towards us so that the glass completely moves away from the screen. In this case, you can grab its edges with your fingers and do the same.
How to stick glass on iPhone 6 and other devices
For everything to go perfectly, you need to stick the glass in a clean room where there is no dust. Before sticking the glass, you need to take a lint-free cloth or a simple cloth, wet the display a little with a cleaning agent or alcohol. This is necessary to clean the surface and remove fatty elements from it.
The gluing procedure is as follows:
1 A new protective coating for the display is taken in hand. As with removal, hands should be clean and dry. Or you need to wear gloves. 2 Remove the protective film covering the sticky surface. To do this, you need to pick it up by the tongue and pull. 3 And how to glue the element itself? The glass should be kept as close to the iPhone display as possible so that small particles of debris or dust do not get on it. After all, any surface tends to quickly accumulate dust. 4 Position the glass cover a few millimeters from the display, align and center it. When gluing, you need to act carefully and carefully make sure that all the holes for the keys, speaker and other elements match. 5 Further, the protective glass on the iPhone 5 falls closer to the screen. Lightly pressing and smoothing movements level the surface. So easily we were able to glue the glass to the display. 6 The surface is wiped with a dry cloth. 7 The glued element that protected the glass is removed from above.If at the end of the procedure you see small dust particles under the protective element, you can peel off part of the glass and blow it out with a vacuum cleaner or remove it with tweezers. Then you need to glue the element back again. How to re-glue glass, you already know.
Now you know how to stick a protective glass on an iPhone. There is nothing complicated in this procedure, replacing the glass on the iPhone 5S is as easy as shelling pears. Gluing the protective glass on the iPhone must be carefully prepared. And the main thing here is to keep everything clean.
Which is better - glass or film?
The answer is obvious - of course, it is better to opt for glass protection. But the point is not only in shock-resistant properties, but also in durability. One has only to note that the glass on an iPhone 4 or another version of the gadget costs twice as much as a regular film.
So the final choice is up to the user. Think for yourself - what is better - to pay more, but in the future to avoid expensive device repairs or save now, but then lay out a lot of money. Screen replacement is one of the most expensive types of Apple gadget repairs. But, on the other hand, the film is also not a bad option.
As a result, the summary will be as follows. The film is affordable. It protects the display from small scratches, removes glare and covers the entire screen. Do I need a protective film for the iPhone screen, given its characteristics? Certainly yes. Moreover, its cost is low, and how to stick a film is an even simpler task than in the case of glass.
Glass is an expensive option. It gives glare, but transmits light to the maximum, and also reliably protects against strong falls and deep cracks. And if you've found a way to save up for an iPhone, you won't be satisfied with the cheap security options. In any case, knowing how to save up for an expensive device, you can find funds for good accessories for the iPhone 6S or other device.
The number one question for everyone who broke the iPhone.
People are furious, offended when they are told: we do not recommend changing the glass on the iPhone. But in vain.
You can change it, it's not a problem. Just in the end it will cost you more. This will be confirmed to you in any service.
Why is that? I decided to turn to proven masters and find out what was the matter. What are they afraid of?
What is the difference between "glass" and "module"
Let's get straight to the terminology.
Glass: a polarizing film and a sensor layer are installed on a special film or gel to it, which recognizes touches. If only the glass is broken, then in most cases the image on the screen does not deteriorate, but pixels often begin to burn out and yellow spots and streaks appear.
Display: right - "the matrix". On models 3G and 3GS, the matrix is installed separately from the glass, and each spare part can be replaced separately without much difficulty. On other models, it is a tightly glued modular assembly.
Display module: is a single construction of glass, matrix, touch part, polarizing film, backlight and mounting frame. Of course, loops are an integral part.
So why does no one allow glass to be changed or are they trying to dissuade?
1. Glass must be changed under sterile conditions
No, you don't understand. Not just in a more or less clean room without air movement and dust. Conditions must be ideal, just sterile.
Why? Any speck of dust caught between the glass and the display can spoil the whole procedure. Even if you don’t notice it right away, over time (and temperature changes) a crack from internal pressure may appear in this place. Such a marriage, by the way, sometimes occurs even in factory modules and new iPhones - stories about iPhones whose screens burst “by themselves”.
Of course, most experimental devices are “lucky”: even with dust between the glass and the display, the owners sell or break the iPhone before something happens. At best, you will walk with visible dots that are noticeable when the backlight is turned on. At worst, well, you get the idea.
2. The procedure takes a lot of time
Broken glass is very difficult to remove from an old module, even if it itself is not damaged in any way. Small fragments and real glass dust are often almost invisible to the eye. But to install new glass, the surface of the module must be surgically clean.
It turns out that the very removal of glass takes at least an hour of diligent work to remove residues and fragments. And the whole procedure from start to finish can take from two to six hours of work by one master.
Compare this to a 20-minute module replacement procedure, and not wanting to deal with glass becomes logical. And we haven't even finished...
3. The equipment does not compare with the factory
Machine example (Google Images)
Of course, not every service will replace the display manually. Some buy machines from China for dense and noticeably better glass installation. Seems great, doesn't it?
The problem with all these machines is that they are not perfect. This concerns both the procedure, and the design, and their calibration. Sometimes (but rarely, which at least pleases) such machines can damage the screen module in the process. This means that the service will still have to install a new one - and lose money on it.
It is clear that we do not care about their problems - a light bulb. Or not? Some damage is not immediately noticeable, then you will come for a guarantee for the work ... and still get a new module. A losing situation, no matter what.
4. Glass gluing does not guarantee results.
The last and the same sad moment. Bonding is not a panacea. Sometimes, after light falls, temperature changes (or strong heating of the device), the glass still begins to peel off the display. Air bubbles appear and then burst. And again you go to the service.
It is important that the procedure can be done cheaply only if the matrix does not have any damage or visible defects. These can be: yellow streaks around the perimeter of the screen, pink spots, broken pixels, translucent vertical stripes and, of course, any cracks. The touchscreen should work perfectly without crashes and broken lines.
In all other cases, you will have to replace the entire display module at a standard price, and maybe even higher than it actually is - given that you have already had to spend time arriving at the service and diagnosing. But it would be easier to pay extra.
Let's be serious: the module is better
I do not pretend to be the ultimate truth. To each his own. But I think that module is always preferable to glass. In terms of time, quality of work and even the consequences after the replacement.
Maybe absolutely all the masters agree with me? :) For some reason it seems that yes.
You can replace the display module for any iPhone at DamProdam Repair. It takes only 30 minutes, and after that you get a guarantee for work and a perfectly working device. The cost depends on the device, but there are no supernatural amounts:
- iPhone 5/5s/5c: 6 190 rubles and protective glass / film as a gift.
- iPhone 6: 8 490 rubles
- iPhone 6 Plus: 9 990 rubles
- iPhone 6s: 21 990 rubles
- iPhone 6s Plus: 27 990 rubles
- iPhone 4/4s: 2 500 rubles
Protective glass is a special coating made of high-strength chemical glass, which is resistant to mechanical damage, scratches and chips. By installing additional protection on the screen of your iPhone, you will protect the display from possible shocks, thereby extending its service life.
Protective glass features
Comparing protective glass and film, there are a huge number of advantages on the side of the glass coating.
- with a thickness of only 0.25 mm, a high level of strength;
- special oleophobic coating eliminates the appearance of fingerprints and other fatty contaminants;
- many types of glass have a nano-coating, thanks to which the smoothness of the glass prevails even in front of a conventional display;
- the glass is attached to the screen using a silicone base - shifts and air bubbles are excluded;
Among the varieties of protective flexible glasses, there are models with hemmed edges and without. In the first case, the edges of the protective coating are rounded, which makes the glass almost invisible, and the edges of the glass do not crumble upon impact.
How to remove the protective glass?
Despite the fact that the life of the protective glass is many times longer than the life of the film, there comes a time when the coating needs to be changed. The silicone-based glass is firmly in contact with the main display, so it will take some skill to remove the protection.
Tools required to remove the protective glass:
- Microfiber cloth (small).
- Strong floss or special floss for cleaning teeth.
- Needle.
The process of removing the film itself is not complicated, but you need to be as careful as possible, otherwise the flexible glass will constantly stick again.
Under one of the edges that are more convenient for work, pry the thread. To do this, carefully move the edge of the glass with a sharp needle and immediately place a napkin so that the base does not stick again. For convenience, it is better to remove the glass with a partner, you will be able to remove the old protective coating more quickly and efficiently.
It is worth noting that this number of tools is designed to remove undamaged glass. But if the surface is split, then more painstaking work and additional items are required. If you are afraid to remove damaged glass yourself or do not have work experience, contact the professionals. The company that repairs Apple equipment in Nizhny Novgorod "MakeMeApple" will help you with this. You can leave a request using the website or by calling the phone.
If you need to replace the protective glass on the iPhone 6, seek help from professionals who offer their services in Yuda. Not only representatives of official iPhone services in Moscow are registered on the site, but also reliable private masters who can change the damaged screen of your iPhone 6 at an affordable price, installing a new one quickly and efficiently.
It is important to understand that the screen module in iPhone 6 consists of several layers:
- liquid crystal display
- sensor
- protective glass
- polarizing filter film
You may need to replace the glass on your iPhone 6 if, as a result of a fall or other strong impact, mechanical damage has formed on it - cracks, chips or scratches. All this not only spoils the appearance of the 6 series smartphone, but also:
- endangers your health, because the sharp edges of the glass on the iPhone are easy to cut yourself
- Dust and moisture can get inside the iPhone 6 through cracks, which is fraught with more serious malfunctions in the mobile device.
- shards of glass being pushed into the iPhone 6 can damage the display or touchscreen, resulting in a more complicated and expensive repair
In case of damage to the protective glass of the iPhone, the entire screen module must be replaced. This is a very expensive procedure. If you need an inexpensive replacement for a cracked iPhone screen, you should contact the performers of the Yudu website.
They will be able to replace the protective components of the iPhone 6 in the shortest possible time. The process of such a repair is very complicated, but Yudu performers have extensive experience working with iPhones. In addition, they have at their disposal professional equipment and all the necessary tools to perform the work.
How long does it take to change the screen?
The time it takes to install a protective new glass on an iPhone 6 can vary significantly. When you only need to install a screen module, replacing a damaged glass on an iPhone 6 will take no more than half an hour. In the event that, after a free diagnostic, it was decided that it was necessary not only to replace the protective component on the iPhone 6 series, but also to perform other repair work, the master would need several hours to restore the equipment.
In addition, the timing is affected by the availability of a spare screen module or iPhone 6 glass, as well as the remoteness of the service center. Given the traffic congestion in Moscow, it is sometimes difficult to get to remote areas of the capital.
If you order a replacement for the damaged iPhone 6 glass from the performers of the Yudu website, your smartphone can be restored at home. Call the master to your house and thereby significantly reduce the time required to repair your iPhone 6.
You can be convinced of the high qualification of the master by reading the reviews of previous customers, which you will find in the profile of a particular artist. A professional specialist will give you the necessary guarantees that glass replacement for iPhone 6 will be performed with the highest quality, quickly and at an affordable price.
If you prefer to repair equipment in official services, choose a workshop that is located near you. To speed up the process of replacing components, you can use the delivery service. The courier will pick up your damaged iPhone 6 directly from your home or office and deliver the already restored one to any specified address in Moscow (including outside the Moscow Ring Road).
Masters offering their services on the Yudu website use only original spare parts or similar components from reliable manufacturers to repair iPhone smartphones. In combination with excellent professional skills, this allows Yudu performers to perform their work with the highest quality.
The specialists registered on our website have undergone a thorough check, confirming the accuracy of the data. All masters are qualified and responsible. Therefore, trusting the replacement of broken glass for iPhone 6 to the performers of the Yudu website, you receive the necessary quality guarantees.
Service cost
iPhone 6 glass replacement costs vary. First of all, prices depend on the cost of the spare part that the master will change in the mobile device. The specialist will diagnose the iPhone 6 for free and, having established how badly the 6 series smartphone is damaged, will choose a method of repairing it.
If you have broken the iPhone 6 screen (its sensor, display or polarizing film were damaged), replacing the iPhone 6 glass alone is indispensable. The front panel of the mobile device is changed as an assembly. Such a repair of a 6 series phone will cost from 7 to 10 thousand rubles, or even more. About how much it costs to replace glass on an iPhone 6, you can find out from the performers of the Yuda site individually.
In addition, the cost of replacing the protective components of the screen is affected by:
- required urgency to replace broken iPhone 6 glass
- qualification of the master who is entrusted with repairing the iPhone
- need for additional services
If you need to replace the glass on your iPhone 6, contacting Yuda, you can order the services of professionals at a low price. All specialists registered on our website work directly with customers, so you do not have to pay intermediaries. Thanks to this, the services of a certified master will cost you about 20% cheaper than the prices of Moscow service centers.
To save on iPhone 6 repair, sign an agreement with the master that you will service your smartphone only with him. This will allow you to change the glass on the iPhone 6 and fix other breakdowns at a discount. In addition, you will receive additional guarantees of quality and a high level of service for your iPhone mobile device.
Where to order services if you need to change the screen?
If you need to order services for replacing damaged iPhone 6 glass, you should create a task on the Yudu website. Immediately after publication, it will be available to all registered performers. Specify in your application:
- how numerous and serious are the chips or cracks on the glass of the iPhone 6
- whether the iPhone is working correctly - as a result of a fall or other impact, in addition to external damage, internal breakdowns could also occur (they are indicated by incorrect operation of the iPhone 6 sensor and other malfunctions)
- urgency to replace a broken screen, glass iPhone 6
Yudu site performers work throughout Moscow. One of them will definitely be close to you and will be able to quickly come to replace the screen or broken glass of the iPhone 6. The service works around the clock and seven days a week, so you can send an online repair request at any time convenient for you.
Professional specialists registered on the Yudu website will contact you as soon as possible to offer their services. The required replacement of glass will be made by them as quickly as possible. You just have to choose a master who installs iPhone 6 glasses efficiently and inexpensively. This is very easy to do by reading the reviews left by previous customers on the Yudu website, as well as the rating of the specialist on the site.
To replace the protective glass on the iPhone 6 was performed on the best terms, contact the professionals who quickly fix any breakdowns of mobile devices.
Loading...